← Ireland

S.I. No. 422/2011 - European Communities (Road Vehicles: Type-Approval) (Amendment) Regulations 2011.

S.I. No. 422/2011 - European Communities (Road Vehicles: Type-Approval) (Amendment) Regulations 2011. Skip to content Disclaimer Feedback Helpdesk Gaeilge Léim go dtí an t-ábhar Séanadh Aiseolas Deasc chabhrach English Gaeilge English Produced by the Office of the Attorney General Táirgthe ag Oifig an Ard-Aighne Home Legislation Acts of the Oireachtas Statutory Instruments Pre-1922 Legislation Constitution External Resources Bills (Houses of the Oireachtas) Iris Oifigiúil / Official Gazette Revised Acts (LRC) Classified List of Legislation (LRC) Translations (acts.

  1. ie)Translations (Houses of the Oireachtas) Government Publications for Sale EU Law (EUR-Lex) FAQ Disclaimer Feedback Helpdesk Search Baile Reachtaíocht Achtanna an Oireachtais Ionstraimí Reachtúla Reachtaíocht Réamh-1922 Bunreacht Acmhainní Seachtracha Billí (Tithe an Oireachtais) Iris Oifigiúil Achtanna Athbhreithnithe (CAD) (An Coimisiún um Athchóiriú an Dlí) Liosta Rangaithe Reachtaíochta Aistriúcháin (achtanna.
  2. ie)Aistriúcháin (Tithe an Oireachtais) Foilseacháin Rialtais ar Díol Dlí AE (EUR-Lex) CCanna (Ceisteanna Coitianta) Séanadh Aiseolas Deasc chabhrach Cuardach TitleTeideal Year(
  3. s)or rangeBliain nó blianta nó raon TypeCineál All Legislation Acts Statutory Instruments Advanced SearchCuardach Casta HomeBaile Statutory InstrumentsIonstraimí Reachtúla 2011 S.I. No. 422/2011 - European Communities (Road Vehicles: Type-Approval) (Amendment) Regulations 2011. S.I. No. 422/2011 - European Communities (Road Vehicles: Type-Approval) (Amendment) Regulations 2011. AmendmentsLeasuithe Download PDF Íoslódáil PDF Notice of the making of this Statutory Instrument was published in “Iris Oifigiúil” of 12th August, 2011. I, LEO VARADKAR, Minister for Transport, Tourism and Sport in exercise of the powers conferred on me by section 3 of the European Communities Act 1972 (No. 27 of 1972), as amended by the European Communities Act 2007 (No. 18 of 2007), and for the purpose of giving further effect to Directive 2007/46/EC of the European Parliament and of the Council of 5 September 20071 , to the Directives specified in Schedule 1 and, as regards their required administrative procedures, to the Regulations therein specified, in so far as those Directives apply to the type approval of motor vehicles and their trailers, components, systems and separate technical units specified in Directive 2007/46/EC1, hereby make the following regulations: 1. These Regulations may be cited as the European Communities (Road Vehicles: Type-Approval) (Amendment) Regulations 2011. 2. The European Communities (Road Vehicles: Type-Approval) Regulations 2009 ( S.I. No.158 of 2009 ) are amended— (
  4. a)by the substitution of the following for 20

(13)(b) and renumbering of existing subparagraphs
(13)A national small series certificate of conformity must be in the same format as that prescribed in Annex IX to the Framework Directive for an EC certificate of conformity relating to a vehicle of the same category and class containing such particulars as are relevant to the vehicle in respect of which it is issued, except that: (
  1. a)the certificate must carry the heading “National Small Series Certificate of Conformity (Ireland)”; (
  2. b)Side 1 is amended by the insertion of the following; “0.11 (
  3. i)Speedometer: Metric only / metric and imperial (
  4. ii)Does any dimension exceed the limits of 7.3 of Directive 97/27/EC as amended? yes/no” (
  5. c)for each reference to an EC type-approval there must be substituted a reference to a national small series type approval, and (
  6. d)for “EC type-approved”, in each place the expression occurs, there must be substituted “nationally type-approved”. (
  7. b)by substituting for Schedule 1, as inserted by Regulation 2(
  8. b)of the European Communities (Road Vehicles: Type-Approval) (Amendment) Regulations 2010, the following: “SCHEDULE 1 ENTRY INTO SERVICE DIRECTIVES 1 Council Directive 70/157/EEC of 6 February 1970 on sound level and exhaust systems (O.J. L42 of 23.2.70, p.16 (S.E. 1970
(1))) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L73 14 27.3.1972 Commission Directive 73/350/EEC of 7 November 1973 L321 33 22. 11.1973 Council Directive 77/212/EEC of 8 March 1977 L66 33 12. 3.1977 Commission Directive 81/334/EEC of 13 April 1981 L131 6 8. 5.1981 Commission Directive 84/372/EEC of 3 July 1984 L196 47 26. 7.1984 Council Directive 84/424/EEC of 3 September 1984 L238 31 6. 9.1984 Act of Accession of Spain and Portugal L302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L192 43 11.7.1987 Commission Directive 89/491/EEC of 17 July 1989 L238 43 15.8.1989 Council Directive 92/97/EEC of 10 November 1992 L371 1 19. 12.1992 Act of Accession of Austria, Sweden and Finland C241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L1 1 1.1.1995 Commission Directive 96/20/EC of 27 March 1996 L92 23 13. 4.1996 Commission Directive 1999/101/EC of 15 December 1999 L334 41 28. 12.1999 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L363 81 20.12.2006 Commission Directive 2007/34/EC of 14 June 2007 L155 49 15. 6.2007 2 Council Directive 70/220/EEC of 20 March 1970 on air pollution by emissions from motor vehicles (O.J. L76 of 6.4.70, p.1 (S.E. 1970 (I))) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L 73 14 27.3.1972 Council Directive 74/290/EEC of 28 May 1974 L 159 61 15. 6.1974 Commission Directive 77/102/EEC of 30 November 1976 L 32 32 3. 2.1977 Commission Directive 78/665/EEC of 14 July 1978 L 223 48 14. 8.1978 Council Directive 83/351/EEC of 16 June 1983 L 197 1 20. 7.1983 Council Directive 88/76/EEC of 3 December 1987 L 36 1 9. 2.1988 Council Directive 88/436/EEC of 16 June 1988 L 214 1 6. 8.1988 Council Directive 89/458/EEC of 18 July 1989 L 226 1 3. 8.1989 Commission Directive 89/491/EEC of 17 July 1989 L 238 43 15.8.1989 Council Directive 91/441/EEC of 26 June 1991 L 242 1 30. 8.1991 Council Directive 93/59/EEC of 28 June 1993 L 186 21 28. 7.1993 Directive 94/12/EC of the European Parliament and the Council of 23 March 1994 L 100 42 19.4.1994 Commission Directive 96/44/EC of 1 July 1996 L 210 25 20. 8.1996 Directive 96/69/EC of the European Parliament and of the Council of 8 October 1996 L 282 64 1.1..1996 Commission Directive 98/77/EC of 2 October 1998 L 286 34 23. 10.1998 Directive 98/69/EC of the European Parliament and of the Council of 13 October 1998 L 350 1 28. 12.1998 Commission Directive 1999/102/EC of 15 December 1999 L 334 43 28. 12.1999 Directive 2001/1/EC of the European Parliament and of the Council of 22 January 2001 L 35 34 6. 2.2001 Directive 2001/100/EC of the European Parliament and of the Council of 7 December 2001 L 16 32 18. 1.2002 Commission Directive 2002/80/EC of 3 October 2002 L 291 20 28. 10.2002 Commission Directive 2003/76/EC of 11 August 2003 L 206 29 15.8.2003 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 including the administrative procedures required by Parliament and Council Regulation 715/2007 of 20 June 2007 on the type approval of motor vehicles and their trailers with respect to emissions from light passenger and commercial vehicles (O.J. L171 of 29.6.2007, p.1) Amended by Official Journal No. page date Commission Regulation 692/2008 of 18 July 2008 L199 1 31.10.2008 Commission Regulation 595/2009 of 18 June 2009 L188 1 18. 7.2009 Corrigenda OJ L 303, 8.11.1988, p. 36 (88/436/EEC) OJ L 270, 19.9.1989, p. 16 (89/458/EEC) OJ L 104, 21.4.1999, p. 31 (98/69/EC) OJ L 104, 21.4.1999, p. 32 (98/69/EC) OJ L 200, 31.7.2009, p.52 (595/2009) 3 Council Directive 70/221/EEC of 20 March 1970 on fuel tanks and rear protective devices (O.J. L76 of 6.4.70, p.23 (S.E. 1970 (I))) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L 73 14 27.3.1972 Commission Directive 79/490/EEC of 18 April 1979 L 128 22 26.5.1979 Commission Directive 81/333/EEC of 13 April 1981 L 131 4 18. 5.1981 Commission Directive 97/19/EC of 18 April 1997 L 125 1 16.5.1997 Directive 2000/8/EC of the European Parliament and of the Council of 20 March 2000 L 106 7 3. 5.2000 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Commission Directive 2006/20/EC of 17 February 2006 L 48 16 18.2.2006 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 65, 15.3.1979, p. 42 (70/221/EEC) OJ L188, 26.7.1979, p.54 (79/490/EEC) OJ L 64, 6.3.2001, p. 39 (2000/8/EC) 4 Council Directive 70/222/EEC of 20 March 1970 on mounting and fixing of rear registration plates (O.J. L76 of 6.4.70, p.25 (S.E. 1970 (I))) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L 73 14 27.3.1972 5 Council Directive 70/311/EEC of 8 June 1970 on steering equipment (O.J. L133 of 18.6.70, p.10) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L 73 14 27.3.1972 Commission Directive 92/62/EEC of 2 July 1992 L 199 33 18. 7.1992 Commission Directive 1999/7/EC of 26 January 1999 L 40 36 13.2.1999 6 Council Directive 70/387/EEC of 27 July 1970 on doors (O.J. L176 of 10.8.70, p.5 (S.E. 1970 (II))) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L 73 14 27.3.1972 Commission Directive 98/90/EC of 30 November 1998 L 337 29 12. 12.1998 Commission Directive 2001/31/EC of 8 May 2001 L 130 33 12.5.2001 Corrigenda Consolidated text of corrigenda to instruments published in Special Edition 1952-72, p. 76 (70/387/EEC) 7 Council Directive 70/388/EEC of 27 July 1970 on audible warning devices (O.J. L176 of 10.8.70, p.12 (S.E. 1970 (II))) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L 73 14 27.3.1972 (adapted by Council Decision of 1 January 1973) L 2 1 1.1.1973 Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 999, 1.1.1973, p. 77 (70/388) OJ L 329, 25.11.1982, p. 31 (70/388) 8 Council Directive 71/320/EEC of 26 July 1971 on braking devices (O.J. L202 of 6.9.71, p.37 (S.E. 1971 (III))) Amended by Official Journal No. page date Act of Accession of Denmark, Ireland and the United Kingdom of Great Britain and Northern Ireland L 73 14 27.3.1972 Commission Directive 74/132/EEC of 11 February 1974 L 74 7 19.3.1974 Commission Directive 75/524/EEC of 25 July 1975 L 236 3 8.9.1975 Commission Directive 79/489/EEC of 18 April 1979 L 128 12 26. 5.1979 Commission Directive 85/647/EEC of 23 December 1985 L 380 1 31.1.1985 Commission Directive 88/194/EEC of 24 March 1988 L 92 47 9.4.1988 Commission Directive 91/422/EEC of 15 July 1991 L 233 21 22.8.1991 Commission Directive 98/12/EC of 27 January 1998 L 81 1 18.3.1998 Commission Directive 2002/78/EC of 1 October 2002 L 267 23 4.10.2002 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 999, 1.1.1973, p. 96 (71/320/EEC) OJ L 247, 23.9.1975, p. 36 (75/524/EEC) OJ L 275, 2.10.1991, p. 36 (91/422/EEC) 9 Council Directive 72/245/EEC of 20 June 1972 on suppression of radio interference (O.J. L152 of 6.7.72, p.15 (S.E. 1972 (II))) Amended by Official Journal No. page date Commission Directive 89/491/EEC of 17 July 1989 L 238 43 15.8.1989 Commission Directive 95/54/EC of 31 October 1995 L 266 1 8.11.1995 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Commission Directive 2004/104/EC of 14 October 2004 L 337 13 13. 11.2004 Commission Directive 2005/49/EC of 25 July 2005 L 194 12 26. 7.2005 Commission Directive 2005/83/EC of 23 November 2005 L 305 32 24.11.2005 Commission Directive 2006/28/EC of 6 March 2006 L 65 27 7.3.2006 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Commission Directive 2009/19/EC of 12th March 2009 L70 17 14. 3.2009 Corrigenda OJ L 056, 2.3.2005, p. 35 (2004/104) 10 Council Directive 72/306/EEC of 2 August 1972 on emission of pollutants from diesel engines for use in motor vehicles (O.J. L190 of 20.8.72, p.1 (S.E. 1972 (III))) Amended by Official Journal No. page date Commission Directive 89/491/EEC of 17 July 1989 L 238 43 15.8.1989 Commission Directive 97/20/EC of 18 April 1997 L 125 21 16.5.1997 Commission Directive 2005/21/EC of 7 March 2005 L 61 25 8. 3.2005 including the administrative procedures required by Parliament and Council Regulation 715/2007 of 20 June 2007 on the type approval of motor vehicles and their trailers with respect to emissions from light passenger and commercial vehicles (O.J. L171 of 29.6.2007, p.1) Amended by Official Journal No. page date Commission Regulation 692/2008 of 18 July 2008 L199 1 31.1.2008 Commission Regulation 595/2009 of 18 June 2009 L188 1 18. 7.2009 Corrigenda OJ L 215, 6.8.1974, p. 20 (72/306/EEC) OJ L 299, 23.11.1977, p. 27 (72/306/EEC) OJ L200, 31.7.2009, p.52 (595/2009) 11 Council Directive 74/60/EEC of 17 December 1973 on certain interior fittings (O.J. L38 of 11.2.74, p.2) Amended by Official Journal No. page date Commission Directive 78/632/EEC of 19 May 1978 L 206 26 29. 7.1978 Directive 2000/4/EC of the European Parliament and of the Council of 28 February 2000 L 87 22 8. 4.2000 Corrigenda OJ L 215, 6.8.1974, p. 20 (74/60/EEC) OJ L 53, 25.2.1977, p. 30 (74/60/EEC) 12 Council Directive 74/61/EEC of 17 December 1973 on anti-theft devices (O.J. L38 of 11.2.74, p.22) Amended by Official Journal No. page date Commission Directive 95/56/EC of 8 November 1995 L 286 1 29. 11.1995 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 215, 6.8.1974, p. 20 (74/61) OJ L 40, 13.2.1998, p. 19 (95/56) 13 Council Directive 74/297/EEC of 4 June 1974 on the behaviour of steering mechanisms in the event of impact (O.J. L165 of 20.6.74, p. 16) Amended by Official Journal No. page date Commission Directive 91/662/EEC of 6December 1991 L366 1 31.1.91 14 Council Directive 74/408/EEC of 22 July 1974 on strength of seats and their anchorages (O.J. L221 of 12.8.74, p.1) Amended by Official Journal No. page date Council Directive 81/577/EEC of 20 July 1981 L 209 34 29. 7.1981 Commission Directive 96/37/EC of 17 June 1996 L 186 28 25. 7.1996 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Directive 2005/39/EC of the European Parliament and of the Council of 7 September 2005 L 255 143 30. 9.2005 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 221, 31.8.1996, p. 71 (96/37/EC) 15 Council Directive 74/483/EEC of 17 September 1974 on external projections (O.J. L266 of 2.10.74, p.4) Amended by Official Journal No. page date Commission Directive 79/488/EEC of 18 April 1979 L 128 1 26. 5.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Commission Directive 2007/15/EC of 14 March 2007 L 75 21 15. 3.2007 16 Council Directive 75/443/EEC of 26 June 1975 on reverse and speedometer equipment (O.J. L196 of 26.7.75, p.1) Amended by Official Journal No. page date Commission Directive 97/39/EC of 24 June 1997 L177 15 5. 7.97) 17 Council Directive 76/114/EEC of 18 December 1975 on location and attachment of statutory plates and inscriptions (O.J. L24 of 30.1.76, p.1) Amended by Official Journal No. page date Commission Directive 78/507/EEC of 19 May 1978 L 155 31 13. 6.1978 Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 56, 4.3.1976, p. 38 (76/114) OJ L 329, 25.11.1982, p. 31 (76/114) 18 Council Directive 76/115/EEC of 18 December 1975 on anchorages for safety belts (O.J. L24 of 30.1.76, p.6) Amended by Official Journal No. page date Council Directive 81/575/EEC of 20 July 1981 L 209 30 29. 7.1981 Commission Directive 82/318/EEC of 2 April 1982 L 139 9 19. 5.1982 Commission Directive 90/629/EEC of 30 October 1990 L 341 14 6. 12.1990 Commission Directive 96/38/EC of 17 June 1996 L 187 95 26. 7.1996 Directive 2005/41/EC of the European Parliament and of the Council of 7 September 2005 L 255 149 30. 9.2005 19 Council Directive 76/756/EEC of 27 July 1976 on lighting and light signalling devices (O.J. L262 of 27.9.76, p.1) Amended by Official Journal No. page date Commission Directive 80/233/EEC of 21 November 1979 L 51 8 25. 2.1980 Commission Directive 82/244/EEC of 17 March 1982 L 109 31 22. 4.1982 Council Directive 83/276/EEC, of 26 May 1983 L 151 47 9. 6.1983 Commission Directive 84/8/EEC of 14 December 1983 L 9 24 12. 1.1984 Commission Directive 89/278/EEC of 28 March 1989 L 109 38 20. 4.1989 Commission Directive 91/663/EEC of 10 December 1991 L 366 17 31.1.1991 Commission Directive 97/28/EC of 11 June 1997 L 171 1 30. 6.1997 Commission Directive 2007/35/EC of 18 June 2007 L 157 14 19. 6.2007 Commission Directive 2008/89/EC of 24 September 2008 L257 14 25. 9.2008 Corrigenda OJ L 111, 30.4.1980, p. 22 (80/233/EEC) OJ L 131.1.5.1984, p. 50 (84/8/EEC) OJ L 135, 22.5.1984, p. 27 (84/8/EEC) 20 Council Directive 76/757/EEC of 27 July 1976 on reflex reflectors (O.J. L262 of 27.9.76, p. 32) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 97/29/EC of 11 June 1997 L 171 11 30. 6.1997 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 21 Council Directive 76/758/EEC of 27 July 1976 on end outline marker lamps, side lamps, rear lamps and stop lamps (O.J. L262 of 27.9.76, p.54) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Commission Directive 89/516/EEC of 1 August 1989 L 265 1 12. 9.1989 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 97/30/EC of 11 June 1997 L 171 25 30. 6.1997 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 22 Council Directive 76/759/EEC of 27 July 1976 on direction indicator lamps (O.J. L262 of 27.9.76, p.71) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Commission Directive 89/277/EEC of 28 March 1989 L 109 25 20. 4.1989 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 1999/15/EC of 16 March 1999 L 97 14 12. 4.1999 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 23 Council Directive 76/760/EEC of 27 July 1976 on rear registration plate lamps (O.J. L262 of 27.9.76, p.85) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 97/31/EC of 11 June 1997 L 171 49 30. 6.1997 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 24 Council Directive 76/761/EEC of 27 July 1976 on headlamps and filament lamps for them (O.J. L262 of 27.9.76, p.96) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Commission Directive 89/518/EEC of 1 August 1989 L 265 15 12. 9.1989 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 1999/17/EC of 18 March 1999 L 97 45 12. 4.1999 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 25 Council Directive 76/762/EEC of 27 July 1976 on front fog lamps and filament lamps for them (O.J. L 262 of 27.9.76, p.122) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 1999/18/EC of 18 March 1999 L 97 82 12. 4.1999 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 26 Council Directive 77/389/EEC of 17 May 1977 on towing devices (O.J. L145 of 13.6.77, p.41) Amended by Official Journal No. page date Commission Directive 96/64/EC of 2 October 1996 L258 26 11.1.96)) Corrigenda O.J. L40 of 13.2.98, p. 19 (77/389) 27 Council Directive 77/538/EEC of 28 June 1977 on rear fog lamps (O.J. L220 of 29.8.77, p.60) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19.11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Commission Directive 89/518/EEC of 1 August 1989 L 265 24 12. 9.1989 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 1999/14/EC of 16 March 1999 L 97 1 12. 4.1999 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 284, 10.10.1978, p. 11 (77/538) 28 Council Directive 77/539/EEC of 28 June 1977 on reversing lamps (O.J. L220 of 29.8.77, p.72) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 97/32/EC of 11 June 1997 L 171 63 30. 6.1997 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 284, 10.10.1978, p. 11 (77/539) 29 Council Directive 77/540/EEC of 28 June 1977 on parking lamps (O.J. L220 of 29.8.77, p.83) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 1999/16/EC of 16 March 1999 L 97 33 12. 4.1999 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 284, 10.10.1978, p. 11 (77/540) 30 Council Directive 77/541/EEC of 28 June 1977 on safety belts and restraint systems (O.J. L220 of 29.8.77, p.95) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Council Directive 81/576/EEC of 20 July 1981 L 209 32 29. 7.1981 Commission Directive 82/319/EEC of 2 April 1982 L 139 17 19. 5.1982 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive 87/354/EEC of 25 June 1987 L 192 43 11.7.1987 Commission Directive 90/628/EEC of 30 October 1990 L 341 1 6. 12.1990 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 96/36/EC of 17 June 1996 L 178 15 17. 7.1996 Commission Directive 2000/3/EC of 22 February 2000 L 53 1 25. 2.2000 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Directive 2005/40/EC of the European Parliament and of the Council of 7 September 2005 L 255 146 30. 9.2005 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 105, 26.4.2005, p. 5 (2000/3/EC) 31 Council Directive 77/649/EEC of 27 September 1977 on field of vision (O.J. L267 of 19.10.77, p.1) Amended by Official Journal No. page date Commission Directive 81/643/EEC of 29 July 1981 L 231 41 15.8.1981 Commission Directive 88/366/EEC of 17 May 1988 L 181 40 12. 7.1988 Commission Directive 90/630/EEC of 30 October 1990 L 341 20 6. 12.1990 Corrigenda OJ L 150, 6.6.1978, p. 6 (77/649/EEC) 32 Council Directive 78/316/EEC of 21 December 1977 on identification of controls, tell-tales and indicators (O.J. L81 of 28.3.78, p.3) Amended by Official Journal No. page date Commission Directive 93/91/EEC of 29 October 1993 L284 25 19. 11.93 Commission Directive 94/53/EC of 15 November 1994 L299 26 22. 11.94 33 Council Directive 78/318/EEC of 21 December 1977 on windscreen wiper and washer systems (O.J. L81 of 28.3.78, p.49) Amended by Official Journal No. page date Commission Directive 94/68/EC of 16 December 1994 L 354 1 31.1.1994 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 194, 19.7.1978, p. 30 (78/318) 34 Council Directive 78/549/EEC of 12 June 1978 on wheel guards (O.J. L168 of 26.6.78, p.45) Amended by Official Journal No. page date Directive 94/78/EC of 21 December 1994 L354 10 31.1.94 35 Council Directive 78/932/EEC of 16 October 1978 on head restraints (O.J. L325 of 20.11.78, p.1) Amended by Official Journal No. page date Act of Accession of Greece L 291 17 19. 11.1979 Act of Accession of Spain and Portugal L 302 23 15. 11.1985 Council Directive of 25 June 1987 L 192 43 11.7.1987 Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 329, 25.11.1982, p. 31 (78/932) 36 Council Directive 80/1268/EEC of 16 December 1980 on fuel consumption of motor vehicles (O.J. L375 of 31.12.80, p.36) Amended by Official Journal No. page date Commission Directive 89/491/EEC of 17 July 1989 L 238 43 15.8.1989 Commission Directive 93/116/EC of 17 December 1993 L 329 39 30. 12.1993 Commission Directive 1999/100/EC of 15 December 1999 L 334 36 28. 12.1999 Directive 2004/3/EC of of the European Parliament and of the Council of 11 February 2004 L49 36 19. 2.2004 Corrigenda OJ L 42, 15.2.1994, p. 27 (93/116/EC) OJ L 163, 4.7.2000, p. 38 (1999/100/EC) 37 Council Directive 80/1269/EEC of 16 December 1980 on engine power of motor vehicles (O.J. L375 of 31.12.80, p.46) Amended by Official Journal No. page date Commission Directive 88/195/EEC of 24 March 1988 L 92 50 9.4.1988 Commission Directive 89/491/EEC of 17 July 1989 L 238 43 15.8.1989 Commission Directive 97/21/EC of 18 April 1997 L 125 31 16.5.1997 Commission Directive 1999/99/EC of 15 December 1999 L 334 32 28.12.1999 including the administrative procedures required by Parliament and Council Regulation 595/2009 of 18 June 2009 L188 1 18. 7.2009 Corrigenda OJ L 105, 26.4.1988, p. 34 (88/195/EEC) OJ L200, 31.7.2009, p.52 (595/2009) 38 Council Directive 89/297/EEC of 13 April 1989 on lateral protection (side guards) (O.J. L124 of 5.5.89, p.1) 39 Council Directive 91/226/EEC of 27 March 1991 on spray-suppression systems (O.J. L103 of 23.4.91, p.5) Amended by Official Journal No. page date Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Commission Directive 2010/19/EU of 9 March 2010 L72 17 20.3.2010 40 Council Directive 92/21/EEC of 31 March 1992 on masses and dimensions of certain motor vehicles (O.J. L129 of 14.5.92, p.1) Amended by Official Journal No. page date Commission Directive 95/48/EC of 20 September 1995 L 233 73 30. 9.1995 Corrigenda OJ L 14, 22.1.1993, p. 29 (92/21) OJ L 252, 20.10.1995, p. 27 (95/48) OJ L 304, 16.12.1995, p. 60 (95/48) 41 Council Directive 92/22/EEC of 31 March 1992 on safety glazing and glazing materials (O.J. L129 of 14.5.92, p.11) Amended by Official Journal No. page date Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Commission Directive 2001/92/EC of 30 October 2001 L 291 24 8. 11.2001 42 Council Directive 92/23/EEC of 31 March 1992 on tyres (O.J. L129 of 14.5.92, p.95) Amended by Official Journal No. page date Act of Accession of Austria, Sweden and Finland C 241 21 29.8.1994 (adapted by Council Decision 95/1/EC, Euratom, ECSC) L 1 1 1.1.1995 Directive 2001/43/EC of the European Parliament and of the Council of 27 June 2001 L 211 25 4. 8.2001 Commission Directive 2005/11/EC of 16 February 2005 L 46 42 17. 2.2005 43 Council Directive 92/24/EEC of 31 March 1992 on speed limitation devices (O.J. L129 of 14.5.92, p.154) Amended by Official Journal No. page date Directive 2004/11/EC of the European Parliament and of the Council of 11 February 2004 L 44 19 14. 2.2004 44 Council Directive 92/114/EEC of 17 December 1992 on external projections forward of the cab’s rear panel of motor vehicles of category N (O.J. L409 of 31.12.92, p.17) 45 Directive 94/20/EC of the European Parliament and of the Council of 30 May 1994 on mechanical coupling devices of motor vehicles and their trailers and their attachment to those vehicles (O.J. L195 of 29.7.94, p.1) Amended by Official Journal No. page date Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 46 Directive 95/28/EC of the European Parliament and of the Council of 24 October 1995 on burning behaviour of materials used in the interior construction of certain categories of motor vehicles (O.J. L281 of 23.11.95, p.1) Amended by Official Journal No. page date Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 47 Directive 96/27/EC of 20 May 1996 on the protection of occupants of motor vehicles in the event of a side impact (OJ L 169, 8.7.1996) Corrigenda OJ L 102, 19.4.1997, p. 46 (96/27) 48 Directive 96/79/EC of the European Parliament and of the Council of 16 December 1996 on the protection of occupants of motor vehicles in the event of a frontal impact (O.J. L18 of 21.1.1997, p.1) Amended by Official Journal No. page date Commission Directive 1999/98/EC of 15 December 1999 L 9 14 13. 1.2000 Corrigenda OJ L 83, 25.3.1997, p. 23 (96/79) 49 Directive 97/27/EC of the European Parliament and of the Council of 22 July 1997 relating to the masses and dimensions of certain categories of motor vehicles and their trailers (OJ L 233, 25.8.1997, p.1) Amended by Official Journal No. page date Directive 2001/85/EC of the European Parliament and of the Council of 20 November 2001 L 42 1 13. 2.2002 Commission Directive 2003/19/EC of 21 March 2003 L 79 6 26. 3.2003 Corrigenda OJ L 125, 21.5.2003, p. 14 (2001/85/EC) 50 Directive 98/91/EC of the European Parliament and of the Council of 14December 1998 relating to motor vehicles and their trailers intended for the transport of dangerous goods by road (OJ L 11.1.1.1999, p.25) 51 Directive 2000/40/EC of the European Parliament and of the Council of 26 June 2000 on the approximation of the laws of the Member States relating to the front underrun protection of motor vehicles (OJ L 203, 10.8.2000, p.9) Amended by Official Journal No. page date Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 52 Directive 2001/56/EC of the European Parliament and of the Council of 27 September 2001 on heating systems (O.J. L292 of 9.11.2001, p.21) Amended by Official Journal No. page date Act concerning the conditions of accession of the Czech Republic, the Republic of Estonia, the Republic of Cyprus, the Republic of Latvia, the Republic of Lithuania, the Republic of Hungary, the Republic of Malta, the Republic of Poland, the Republic of Slovenia and the Slovak Republic and the adjustments to the Treaties on which the European Union is founded L 236 33 23.9.2003 Commission Directive 2004/78/EC of 29 April 2004 L 231 69 30. 6.2004 Commission Directive 2006/119/EC of 27 November 2006 L 330 12 28. 11.2006 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 53 Directive 2001/85/EC of the European Parliament and of the Council of 20 November 2001 on buses and coaches (O.J. L42 of 13.2.2002, p.1) Amended by Official Journal No. page date Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 Corrigenda OJ L 125, 21.5.2003, p. 14 (2001/85) 54 Directive 2003/97/EC of the European Parliament and of the Council of 10 November 2003 on the type-approval of devices for indirect vision and of vehicles equipped with these devices (O.J. L25, 29.1.2004, p.1) Amended by Official Journal No. page date Commission Directive 2005/27/EC of 29 March 2005 L 81 44 30. 3.2005 Council Directive 2006/96/EC of 20 November 2006 L 363 81 20.12.2006 55 Directive 2005/55/EC of the European Parliament and of the Council of 28 September 2005 on emission of gaseous and particulate pollutants from diesel or gas engines for use in vehicles (O.J. L275 of 20.10.2005, p.1) Amended by Official Journal No. page date Commission Directive 2005/78/EC of 14 November 2005 L 313 1 29.11.2005 As amended by Commission Directive 2006/81/EC L362 92 20.12.2006 Commission Directive 2006/51/EC of 6 June 2006 L 152 11 7. 6.2006 Commission Directive 2008/74/EC of 18 July 2008 L 192 51 19. 7.2008 including the administrative procedures required by Parliament and Council Regulation 595/2009 of 18 June 2009 L188 1 18. 7.2009 Corrigenda OJ L200, 31.7.2009, p.52 (595/2009) 56 Directive 2005/64/EC of the European Parliament and of the Council of 26October 2005 on reusability, recyclability and recoverability (O.J. L310 of 25.11.2005, p.10) Amended by Official Journal No. page date Commission Directive 2009/1/EC of 7 January 2009 L9 31 14. 1.2009 57 Directive 2006/40/EC of the European Parliament and of the Council of 17 May 2006 on emissions from air-conditioning systems (O.J. L161 of 14.6.2006, p.12) including the administrative procedures required by Official Journal No. page date Commission Regulation (EC) No.706/2007 of 21 June 2007 L 161 33 22. 6.2007 ”, and (
  1. c)by substituting for Schedule 3 the following: “SCHEDULE 3 PART 1 Technical Specification and Technical Requirements for National Small Series Type-Approval for Category M Vehicles (small series limit: for M1 is 75 vehicles per type per year; for M2 or M3 is 250 vehicles per type per year) To enable representative testing the vehicle will be delivered in a presentable state and capable of being laden to maximum authorised weight. A representative of the manufacturer must be present to enable access to all parts of the vehicle, to assist in explanation of features of that vehicle, and to cooperate in any testing. Subject / Requirements Exemptions / Variations Test Conditions / Resulting Documentation 1. Sound Level The technical provisions of: • Paragraph 5 to Annex I to Directive 70/157/EEC as last amended by Directive 1999/101/EC or Directive 2007/34/EC Or • Paragraph 6 to UNECE Regulation 51.02 Directive 70/157/EEC, Annex I, paragraphs 5.3.1.1, 5.3.1.2. and 5.3.1.3 shall not apply.Vehicles for which an approval or test report has been issued prior to modification of the exhaust system down stream of the catalyst, a Stationary Noise Test “Stationary Noise Test” means:
  2. a)in the case of a modified exhaust system a stationary test as defined in paragraphs 5.2.3.4.2 and 5.2.3.4.3 of Annex I to Directive 70/157 and shall not exceed the equivalent stationary value recorded on the Certificate of Conformity, Approval Certificate or test report for that vehicle by more than 2dB(A) at 0.5m. Laden or unladen vehicle. Approval or Test Report And For modified systems a Stationary Noise Test
  3. b)in the case of vehicles having a maximum permissible mass exceeding 2800kg fitted with a modified air brake system, a test report is required to paragraph 5.4 of Annex I to Directive 70/157/EC except that this shall not apply if air brake silencers are fitted. Modification of the exhaust system length after last silencer not exceeding 2m is permissible without further test. For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. 2. Emissions (Light Duty Vehicles) The technical provisions of: • paragraph 5 of Annex I to Directive 70/220/EEC as last amended by Directive 2003/76/EC, Row B limit values Or UNECE Regulations 83.05 Applies to M1 and M2 vehicles and M3 with positive ignition. Directive 70/220/EEC as amended shall cease to apply from 2 January 2013. Vehicles are exempt from the requirements of On Board Diagnostic systems. This item does not apply to vehicles approved to item 41. Laden or unladen vehicle. Approval or Test Report And Inspection of modifications (if applicable) Vehicles manufactured on or after 1st January 2012: the technical provisions of Regulation (EC) 715/2007 as amended by Regulation (EC) 692/2008, Annex I, Table 1. Vehicles manufactured on or after 1stSeptember 2016: the technical provisions of Regulation (EC) 715/2007 as amended by Regulation (EC) 692/2008, Annex I, Table 2. Modification of exhaust system length after the last silencer is permissible without any further test. For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. An EC type-approval issued to the most representative base vehicle remains valid irrespective of change in the reference mass Only modifications specified above will be accepted without further test. Any other modifications may be assessed at the discretion of the Approval Authority 3. Fuel Tanks / Rear Protective DevicesFor fuel tanks: The technical provisions of: • Directive 70/221/EEC as last amended by directive 2006/20/EC Fuel tanks for liquid fuels at ambient temperature must:comply with the requirements given in column 1 except that the approval or test report, need not be for the same vehicle type: and subsequent modifications to the pipework or relocation of a tank excluding the tank, the cap/filler device or the venting device, may be accepted by the Approval authority. Installation Check that the fuel tank or rear underrun device has been correctly installed in accordance with the technical requirements. Fuel tanks for gaseous fuels: Approval or Test Or • For liquid fuel tanks: UNECE Regulation 34.02. For vehicles using gaseous fuels: UNECE Regulations 67.01 and 115 for LPG. UNECE Regulations 110.00 and 115 for CNG. Note: The requirements for liquid fuel tanks apply only to fuel tanks used primarily for the propulsion of the vehicle. Rear Protection Device: An Installation check must be made to confirm that the rear protective device as a separate technical unit is of a type for which: a type approval or test report has been issued; or ReportFuel tanks for liquid fuels at ambient temperature: Approval or Test Report Rear Underrun: Approval or Test Report AndFor rear underrun: The technical provisions of: • Paragraph 5 of Annex II to Directive 70/221/EEC as last amended by directive 2006/20/EC Or • UNECE Regulation 58.01 has been tested and witnessed by the Approval Authority; or calculations have been submitted to the satisfaction of the Approval Authority; and a visual inspection that the device has been correctly installed in accordance with the technical requirements. If the vehicle is fitted with a fuel tank for petrol the fuel tank shall be so constructed that it cannot readily be filled from a petrol pump delivery nozzle which has an external diameter of not less than 23.6mm without the aid of a device (such as a funnel) not fitted to the vehicle. The fuel system, including the fuel tank, shall be so designed, constructed and fitted as to withstand the forces, vibration and corrosive environment to which it is likely to be subject. It shall also be so fitted as to avoid the risk of damage, such as abrasion, due to fouling of other parts, and to minimise the risk of fire in the event of any leakage of fuel. 4. Rear Registration Plate Space The technical provisions of paragraphs 1 and 2 to Directive 70/222/EEC A check that the positional, dimensional and the visibility requirements are met. Approval or Test Report Or A dimensional and the visibility check 5. Steering Effort The technical provisions of: • Directive 70/311/EEC as last amended Or • UNECE Regulation 79.01 Where a vehicle is constructed using a base vehicle of a different category the provisions applicable to the base vehicle category at its maximum mass may apply. For a modified system manoeuvrability test in accordance with paragraph 5 of 1992/62/EEC Laden vehicle. Approval or Test Report 6. Door Latches and Hinges The technical provisions of: • Directive 70/387/EEC as last amended by Directive 2001/31/EC Or • UNECE Regulation 11.03. Applies to M1 vehicles Does not apply to any power operated door which meets the technical requirements of paragraph 7.6.5 of Annex I to Directive 2001/85/EC Approval or Test Report OrEvidence that suitable proprietary parts from approved vehicles are used 7. Audible Warning The technical provisions of: • Paragraph 2 of Annex I to Directive 70/388/EEC as last amended by 87/354/EC Or • Paragraph 14 to UNECE Regulation 28.00 Inspection to confirm the presence of approval marks and operation of the device including a Sound Level Check which is a vehicle test as described in the technical provisions given in column 1 except that a voltage test is not required. Component: Approval or Device must be “e” / “E” marked Vehicle: Approval or Test Report Or Inspection to confirm the presence and operation of the device including a Sound Level Check. 8. Indirect Vision Devices The technical provisions of: • Directive 2003/97/EC Or • UNECE Regulation 46.02. Field of view requirements do not apply to Optional mirrors. “Optional mirrors” are mirrors not intended to give a clear view to the rear, side or front of the vehicle within the fields of vision defined in 2003/97/EC; therefore they are in no way a substitute for rear view mirrors Component Approval: Approval or Device must be “e” / “E” marked Vehicle Approval: Approval or Test Report Specify the numbers and class(
  4. es)of mirror required for each vehicle category. 9. Braking The technical provisions of: • Paragraph 2 of Annex I to Directive 71/320/EEC as last amended by Directive 1998/12/EC and tests as defined in associated Annexes as may be applicable. Or • Paragraph 5 of UNECE Regulation 13.09 or 13H.00 and tests as defined in associated Annexes as may be applicable. For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. Laden and Unladen vehicleApproval or Test Report 10. Radio Interference / Electro-magnetic Compatibility The technical provisions of: • Directive 72/245/EEC as last amended by Directive 2006/28/EC, section 6 of Annex I taking into consideration the exemptions in section 8 and tests specified in Annexes IV to X Or • UNECE Regulation 10.03 Items for which approval has been granted as part of the base of incomplete vehicle approval do not need re-approval. If adding additional electrical/electronic components to the vehicle then these additional components should be “e” / “E” marked. If they are not “e” / “E” marked then the additional components will require EMC testing as per 2004/104/EC and a test report will be required for evidence of this. Components: Approval or Device must be “e” / “E” marked Installation: Approval or Test Report Or A Test / Inspection restricted to a check for “e” / “E” marked components and ESA approval for safety critical items. 11. Diesel Smoke • Directive 72/306/EEC as last amended by Directive 2005/21/EC section 5 of Annex I and tests as defined in Annexes IV and V Or • EC Regulation 715/2007 Or • UNECE Regulation 24.03 A free acceleration test such that the coefficient of absorption of the exhaust emissions from the engine immediately after leaving the exhaust shall not exceed—
  5. a)for an M1 vehicle, 1.5 per metre or
  6. b)for an M2 or M3 vehicle:
  7. i)if the engine of the vehicle is turbo-charged, 3.0 per metre or
  8. ii)in any other case, 2.5 per metre is allowed as an alternative.“co-efficient of absorption” is to be construed in accordance with paragraph 3.5 of Annex VII to Directive 72/306/EEC; “free acceleration” has the same meaning as in Annex II to Directive 77/143/EEC as last amended by Directive 92/55/EEC. A test report for a modified system need only refer to the engine as long as the installation conditions are not violated. Vehicles fitted with proprietary engines which have already been satisfactorily tested for emissions to 72/306 may gain approval for the vehicle based on the engine results provided that similar conditions of installation to those on the test report are used. Where “similar” means installation tolerances in the directive. Data should be provided to show that Intake and Exhaust specifications are within the ranges specified in the 72/306/EEC type approval information document. Directive 72/306/EEC as amended shall cease to apply from 2 January 2013. Approval or Test Report 12. Interior Fittings The essential Technical requirements of: • Directive 74/60/EEC or • ECE Regulation 21.01 Applies to M1 vehiclesThe following shall not apply: Directive 74/60/EEC, Annex I, Paragraphs 5.1.2, 5.2.4, 5.3.4.1, 5.4.2.2, 5.7.1.2 and the second sentence of 5.2.3.1. And ECE Regulation 21.01,paragraphs 5.1.2, 5.2.3.1, 5.2.4, 5.3.4.1, 5.4.2.2, 5.4.2.3, 5.7.1.2. For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. Approval or Test Report 13. Anti-theft and Immobiliser The technical provisions of: • Directive 74/61/EEC as last amended by Directive 95/56/EC.Or • UNECE Regulations 18.03, 97.01 and 116 as applicable. Immobilisers must be approved as part of the base vehicle or as a Separate Technical Unit. Alarms must be approved as part of the base vehicle or as a Separate Technical Unit. The following shall not apply: Directive 74/61/EEC Annex IV, paragraphs 3.9, 4.1.3, 4.1.4, 4.2.4, 4.2.6, and 4.3.5; And UNECE Regulation 18, paragraphs 5.8, 6.1.3, 6.1.4, 6.2.4, 6.2.6, 6.3.5. In the case of devices to prevent unauthorised use the manufacturer may as an alternative to an approval or test report issue a declaration of the device(
  9. s)fitted and that they comply with column 1, and in such case an Installation Check will be conducted including any check the Approval Authority considers necessary and in the case of an immobiliser or alarm system a completed installation certificate. In the case of an immobiliser or alarm system an Installation Check An “Installation Check” means: An inspection of installed components as the approval authority deem necessary and in the case of an immobiliser or alarm system a completed installation certificate. For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. Device to prevent unauthorised use: Approval or Test Report Immobilisers and Alarm Systems Approval or Test report And Installation Check 14. Protective Steering The essential technical provisions of: • Directive 74/297/EEC as last amended by Directive 91/662/EEC Or • UNECE Regulation 12.03 Applies to M1 vehiclesThe requirements according to the category of the base or incomplete vehicle based on maximum mass may apply. Approval or Test Report 15. Seat Strength The technical provisions of: • Directive 74/408/EEC as amended by Directive 2005/39/EC Or • UNECE Regulation 17.07 Side facing seats may be fitted in accordance with Directive 74/408/EEC as amended by Directive 2005/39/EC, Article 3a, paragraph 3, until 20 October 2010. The installation of side facing seats shall be prohibited in vehicles of categories M1, M2 (Class B or III) and M3 (Class B or III). Approval or Test Report 16. Exterior Projections The essential technical requirements of: • Directive 74/483/EEC Or • ECE Regulation 26.03 Applies to M1 vehiclesFor vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply to the cab only. Approval or Test Report 17. Speedometer and Reverse Gear The technical provisions of: • Directive 75/443/EEC as amended by Directive 97/39/EC Or • UNECE Regulation 39.00 This requirement does not apply to a vehicle fitted with a tachograph if the tachograph provides adequate visual indication of speed to the driver. SpeedometerApproval or Test Report Or Tachograph fitted and provides adequate visual indication of speed to the driver.Reverse GearA test to confirm the presence and function of a reverse gear and operation from the driving position. 18. Plates (statutory) The technical provisions of:Directive 76/114/EEC as last amended by Directive 78/507/EEC. AndWhere the vehicle is the subject of a multi stage build a plate is required on completion of each stage as appropriate Inspection to confirm:the presence of a plate bearing details of Make, Model, VIN (or equivalent unique vehicle identifier), and Masses (Maximum Design values for the Axles, Gross Vehicle and Gross Train, King Pin (for semi trailers only)); the initial VIN or unique vehicle identifier is marked on the chassis or other structure on the right hand side of the vehicle. And that it is placed in a clearly visible and accessible position by a method such as hammering or stamping, in such a way that it cannot be obliterated or deteriorate.Where the vehicle is the subject of a multi stage build a plate is required on completion of each stage as appropriate. Inspection 19. Seat Belt Anchorages The technical provisions of: • Directive 76/115/EEC as last amended by Directive 2005/41/EC Or • UNECE Regulation 14.06 Applies to M1, M2 (Class B or III), M3 (Class B or III), And, if fitted, M2 (Class A, I or II), M3 (Class A, I or II) Approval or Test Report 20. Installation of Lighting and Light Signalling Devices The technical provisions of: • Annex II to Directive 76/756/EEC as last amended by 2007/35/EC Or • UNECE Regulation 48.03, Andwhere applicable: Rear Marker Plates to Statutory Instrument 157 of 1985 For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply to the cab. Approval or Test Report All lighting devices must be “e” / “E” marked and of the correct categories to be fitted in appropriate locations; Headlamps must be appropriate for left-hand rule of the road. The manufacturer should provide a list of components, their “e” / “E” numbers and any alternatives covered by test reports. 21. Retro Reflectors, Rear Marker The technical and marking requirements of: • Directive 76/757/EEC as last amended by Directive 97/29/EC Or • UNECE Regulation 3.02 And, 2. Where applicable: Rear Marker Plates to Statutory Instrument 157 of 1985 Approval or Devices must be “e” / “E” marked. 22. End-outline, Front-position (side), Rear-position (side), Stop, Side Marker, Daytime Running Lamps The technical and marking requirements of: • Directive 76/758/EEC as last amended by Directive 97/30/EC Or • For End-Outline, Front-Position (side), Rear-Position (side), and Stop lamps UNECE Regulation 7.02. For Daytime Running Lamps UNECE Regulation 87.00. For Side Marker lamps, UNECE Regulation 91.00 Approval or Devices must be “e” / “E” marked 23. Direction Indicators The technical and marking requirements of: • Directive 76/759/EEC as last amended by Directive 99/15/EC Or • UNECE Regulation 6.01 Approval or Devices must be “e” / “E” marked 24. Rear Registration Plate Lamps The technical and marking requirements of: • Directive 76/760/EEC as last amended by Directive 97/31/EC Or • UNECE Regulation 4.00 Approval or Devices must be “e” / “E” marked 25. Headlamps including bulbs The technical and marking requirements of: • Directive 76/761/EEC as last amended by Directive 99/17/EC Or • Equivalent UNECE Regulations 1.02, 5.02, 8.05, 20.03, 31.02, 98.00 and 112 for headlamps, And UNECE Regulations 2, 37.03 and 99.00 for all lamps (bulbs). An Installation Check will be conducted including any check the Approval Authority considers necessary. A check for left hand rule of the road traffic dipped beam cut off is required. If of self levelling design then a self certification is required. Headlamps: Approval Or Approval and supplementary test report for modificationsLamps (bulbs): Approval or Devices must be “e” / “E” marked Components be “e” marked Installation check 25A. Cornering Lamps Where fitted: the technical and marking requirements of UNECE Regulation 119 Approval or Devices must be “e” / “E” marked 26. Front Fog LampsWhere fitted: the technical and marking requirements of: • Directive 76/762/EEC as last amended by Directive 99/18/EC Or • UNECE Regulation 19.02 Approval or Devices must be “e” / “E” marked 27. Towing Hooks The technical provisions of:Annex II to Directive 77/389/EEC as last amended by Directive 96/64/EC Not Applicable for M1 Approval or Test Report 28. Rear Fog Lamps The technical and marking requirements of: • Directive 77/538/EEC as last amended by Directive 99/14/EC Or • UNECE Regulation 38.00 Approval or Devices must be “e” / “E” marked 29. Reversing Lamps The technical and marking requirements of: • Directive 77/539/EEC as last amended by Directive 97/32/EC Or • UNECE Regulation 23.00 Approval or Devices must be “e” / “E” marked 30. Parking LampsWhere fitted: the technical and marking requirements of: • Directive 77/540/EEC as last amended by Directive 99/16/EC Or • UNECE Regulation 77.00 Approval or Devices must be “e” / “E” marked 31. Seat Belts and Restraint Systems The technical provisions of: • Directive 77/541/EEC as last amended by Directive 2005/40/EC Or • UNECE Regulation 16.05 Full Directive specification required in all seating positions Seat belts which have been specially designed or adapted for use by an adult or young person suffering from some physical defect or disability and intended for use solely by such person are exempt. Any vehicle not required to be fitted with seat belt anchorages is exempted from these requirements. A seat belt bearing an approval may be fitted, whether or not the seat belt has been type approved for the anchorages to which it is fitted, provided that the seat belt complies with the installation requirements. List minimum numbers and classes of seat belt for each vehicle category Components: Approval or Test Report. Devices must be “e” / “E” marked Installation: Approval or Test Report or manufacturer’s test report 32. Forward VisionTechnical requirements of: • Directive 77/649/EEC as amended by 90/630/EEC Or • UNECE Regulation 125 Applies to M1 vehiclesFor vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. Approval or Test Report 33. Identification of Controls, Tell-tales and Indicators The technical provisions of: • Directive 78/316/EEC as amended by Directive 94/53/EC Or • UNECE Regulation 121 Inspection to check that the prescribed controls are marked in accordance with the requirements of the directive. Other optional controls should be readily identifiable and must not be confusable with other symbols show in the Directive and Regulation. Electronic displays shall follow any appropriate priority protocol. Approval or Test Report AndInspection 34. Defrost / Demist The essential technical requirements of Annex I paragraphs 5.1.1 and 5.2.1.of Directive 78/317/EEC For M1 vehicles:For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply if an adequate system is provided in the front. The defrost system must be capable of melting frost or ice on the surface of the windscreen thereby restoring visibility over the bulk of the area prescribed in the washer and wiper section. The demist system must be capable of removing a film of condensate on the inside surface of the windscreen thereby restoring visibility over the bulk of the area prescribed in the washer and wiper section [A test procedure to determine an adequate system is to be defined] For M2 and M3 vehicles: Vehicles shall be fitted with an adequate defrosting and demisting device.“Adequate” means sufficiently effective to ensure adequate visibility through the windscreen under all conditions. Approval or Test Report OrDocumented details of the system plus a functional check Or Where appropriate a check for adequate system. 35. Wash / Wipe The technical requirements of Annex I paragraph 5 of Directive 78/318/EEC For M1 vehicles:For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply if an adequate system is provided in the front. For M2 and M3 vehicles: Vehicles shall be fitted with adequate washing and wiping devices. “Adequate” means sufficiently effective to ensure adequate visibility through the windscreen under all conditions. Approval or Test Report Or Visual inspectionTest to the specifications contained in paragraph 5 of 78/318/EEC. 36. Heating Systems The technical provisions of: • Directive 2006/119/EC, section 3 of Annex II, and Annexes III, VII and VIII.Or • UNECE Regulation 122 Systems using waste heat from the engine cooling system need only be checked for presence and operation. Vehicle manufacturer needs to demonstrate the essential requirements are fulfilled. If air is the medium for heat transfer, conduct a test to ensure that CO levels of air coming from vents is not more that 20ppm above the ‘ambient’ air. Normal exhaust measuring equipment may be sufficiently sensitive. Combustion heaters (if fitted) Approval or Test Report Waste Heat Systems Approval or Test Report Or Installation Check 37. Wheel Guards The technical provisions of Directive 78/549/EEC as amended by 94/78/EC Applies to M1 vehiclesVehicle to comply with dimensional requirements, which can be demonstrated by technical drawing Approval or Test Report or and visual inspection 38. Head Restraints The technical provisions of Directive 78/932/EEC Applies to M1 vehiclesFor vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. This item does not apply to seats not intended for normal use while the vehicle is travelling on a road. Seats that are for use when travelling on a road must be clearly identified to users. Approval or Test Report 39. CO2 Emissions / Fuel Consumption The technical provisions of: • Directive 80/1268/EEC as amended by Directive 2004/3/EC.Or • UNECE Regulation 101 Applies to M1 vehicles Does not apply to vehicles fitted with an engine approved to item 41. May be tested concurrent with Item 2.May accept validated test report from engine supplier or from another vehicle with proven equivalent characteristics. Approval or Test Report 40. Engine Power The technical requirements of: • Directive 80/1269/EEC as amended by Directive 1999/99/EC Or • UNECE Regulation 85 where applicable If standard power unit is fitted the use of the manufacturer’s data or a chassis dynamometer check is permitted. Approval or Test Report 41. Emissions (Euro IV and V) Heavy-duty VehiclesDirective 2005/55/EC as amended by2006/51/EC, Annex I, and Row B1 limit values. Or UNECE Regulation 49.05 Complete or incomplete M1 vehicles manufactured on or after 1 October 2010: Directive 2005/55/EC as amended by 2006/51/EC, Annex I, and Row B2 limit values.Complete or incomplete M2 or M3 vehicles manufactured on or after 1 October 2009: Directive 2005/55/EC as amended by 2006/51/EC, Annex I, and Row B2 limit values. Does not apply to vehicles not fitted with a CI engine except for vehicles fuelled with natural gas or liquefied petroleum gas.Does not apply to vehicles approved under item 2. Modification of exhaust system length after the last silencer is permissible without any further test. For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. Other modifications may be assessed by the Approval Authority. A check will be made that an approved/tested engine is installed in the vehicle, and is marked in accordance with that approval or test report and the intake and exhaust systems are appropriate so as conform to the installation conditions. The approval label on the engine or control unit shall be checked Approval or Test Report AndVisual Check 42. Lateral Protection Not Applicable 43. Spray-suppression systems Not Applicable 44. Masses and Dimensions (cars) The essential technical requirements of Directive 92/21/EEC as amended by 95/48/EC Applies to M1 vehicles Masses and dimension listed in the Road Traffic (Construction and Use of Vehicles) Regulations 2003 (Statutory Instrument No. 5 of 2003) as amended may apply. Approval or Test Report 45. Safety Glazing The technical and marking provisions of: • Directive 92/22/EEC as amended by Directive 2001/92/EC Or • UNECE Regulation 43. Exclusions defined in paragraph 1 of Annex II to Directive 92/22/EEC as amended. For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. Directive 92/22/EEC, Annex III, paragraph 2.1.1 and 2.1.2 do not apply provided that driver’s forward vision is not distorted and that light transmission of at least 70% is maintained. Component: Approval Andall glazing must be e/E marked Installation: Approval or Test Report or manufacturer’s test report and installation check. 46. Tyres The technical provisions and marking requirements of: • Directive 92/23/EEC as last amended by Directive 2005/11/EC Or • UNECE Regulations 30.02 or 30.03, 54 for durability and 117.01 for noise. And In the case of a temporary use spare wheel (if fitted), The technical provisions and marking requirements of: UNECE Regulation 64.01AndThe technical provisions and marking requirements of Regulation (EC) 661/2009 as it relates to tyre wet grip, rolling resistance and rolling noise from the dates shown in that Regulation Installation Check required to ensure that all tyres (except those that are not accessible) are marked in accordance with the directive including the appropriate speed and load ratings for their particular axle locations and the intended use of the vehicle. Check that tyres don’t foul bodywork For vehicles with a maximum mass equal to or exceeding 2500kg the requirements according to the category of the base or incomplete vehicle or of the corresponding N category vehicle based on maximum mass may apply. Component: Approval or Devices must be “e” / “E” marked Installation: Approval or Test Report OrInstallation Check Where markings cannot be checked a declaration will be required from the manufacturer 47. Speed Limitation Devices The technical provisions and marking requirements of: • Directive 92/24/EC as last amended by Directive 2004/11/EC,Or • UNECE Regulation 89. Applies to M2 and M3 vehicles Installation Check for presence, component approval markings and the set speed which must be indicated on a plate in a conspicuous position inthe driver’s compartment. Component: Approval or Devices must be “e” / “E” marked Installation: Approval or Test Report OrInstallation Check 48. Masses and Dimensions The technical provisions of: • Directive 97/27/EC as amended by Directive 2003/19/EC, section 7 of Annex I. Or • UNECE Regulation 107.02, Annex 11. Applies to M2 and M3 vehiclesMasses and dimension listed in the Road Traffic (Construction and Use of Vehicles) Regulations 2003 (Statutory Instrument No. 5 of 2003) as amended may apply.Directive 97/27/EC, Annex I, Paragraph 7.6. does not apply to a motor vehicle having 4 or more axles where the distance between the foremost and rearmost axles exceeds 6.4 m. Approval or Test Report 49. External Projections of Cabs Not Applicable 50. CouplingsWhere fitted, the technical provisions of: • Annex VII to Directive 94/20/EC Or • UNECE Regulation 55.01 Component: Approval Installation: Approval / Test Report 51. Flammability The technical provisions of: • Directive 95/28/EC, section 7 of AnnexI. Or • UNECE Regulation 118. Applies to M3 Class III vehiclesInspection shall confirm by physical examination, all materials are either marked as having an approval to the directive or, if this is not possible, documentary evidence (e.g. approval certificate, report). Approval / Test Report 52. Buses and Coaches Applies to M2 and M3 vehiclesVehicles of Class 1, as an alternative to the Accessibility Requirements in Annex VII of the Directive or Annex 8 or the UNECE Regulation, may comply with Chapters I, II, and III of this Schedule. Approval / Test Report Requirements that are not compatible with the intended use do not apply to the following; • Vehicles containing seating for use only while the vehicle is stationary • vehicles for the secure transport of persons • Vehicles designed for use by the Garda Síochána, security and armed forces, In the case of armoured vehicles, exemption from one or more of the provisions is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply. In the case of any deck of a vehicle without a permanent top, the handrails are required to extend to the ceiling or to a height of not less than 1500mm. A handhold may be substituted for a handrail. A door, not being a service door, may be fitted to the offside of a vehicle. Vehicles of Class B fitted with more than one wheelchair space: In the case of the second and subsequent wheelchair spaces, the space must be not less than 700 mm wide and 1200 mm long. The technical provisions of: • Directive 2001/85/EC, section 7 of Annex I including references to Annex III, IV, V, VI and VIII. Accessibility for vehicles of Class I: The technical provisions of Directive 2001/85/EC Annex VII and Routes and Destination Displays. Vehicles other than Class I: If equipped with devices for people with reduced mobility and/or wheelchairs, shall comply with the relevant requirements of Annex VII as may be applicable to the devices fitted. Optional accessibility approval for vehicles of Class II or III: The technical provisions of Directive 2001/85/EC Annex VII and Routes and Destination Displays. Vehicles of Class I, II or III As an alternative to Directive 2001/85/EC, Annex VIII, paragraph 7.6.1.14 the upper deck gangway shall be connected by one or more intercommunication staircases to the access passageway of a service door or to the lower deck gangway within 3m of a service door. Vehicles of Class A or B As an alternative to Directive 2001/85/EC, Annex I, paragraph 7.11.3.1 a vehicle may be fitted with handrails or handholds on at least one side and in the case of double doors this requirement may be met by a central stanchion or handrail. Vehicles of Class A or B: As an alternative to Directive 2001/85/EC, Annex VII paragraphs 3.6 to 3.8, may comply with Chapter I of this Schedule. Requirements that are not compatible with the intended use do not apply to the following vehicles: In the case of a vehicle of Class III specially designed for the carriage of school children, Annex I to Directive 2001/85/EC shall be amended as follows: (
  10. a)for 225mm in paragraphs 7.7.8.1.1 and 7.7.8.1.2 shall be substituted 200mm; (
  11. b)for 680mm in paragraph 7.7.8.4.1 shall be substituted 650mm; and (
  12. c)for 400mm in paragraph 7.7.8.2.2 shall be substituted 350mm. Paragraph 7.4 of Annex I to Directive 2001/85/EC shall not apply to: (
  13. a)a vehicle of Class B fitted with no more than 16 passenger seats; or (
  14. b)any other single deck vehicle fitted with a Vehicle Stability Function for which an approval has been issued in accordance with UN/ECE Regulation 13.11. Vehicles of Class A & B: The frontal barrier collision test in paragraph 7.6.7.2. of Annex I to Directive 2001/85/EC shall not apply to a vehicle in which all passengers have access to at least two doors, being either a service door or an emergency door, one of which is not a sliding door. Vehicles of Class B:Directive 2001/85/EC, Annex VII, paragraph 3.3.1. shall not apply. Vehicles of Class B with a variable seating or wheelchair arrangement:Directive 2001/85/EC, Annex VII, paragraph 3.4.1. shall not apply to the extent that it requires a pictogram internally adjacent to a priority seat or a wheelchair space.Directive 2001/85/EC, Annex I, paragraph 7.6.7.6.: In the case of: (
  15. i)a manually operated sliding door fitted with a slam lock of the two stage type the activation of the device may be by movement of the door itself; (
  16. ii)a nearside rear door forming part of a pair of doors fitted at the rear of the vehicle the requirements do not apply if that door is capable of being held securely closed by the other door of that pair. Vehicles of Class IMay as an alternative to the table in Directive 2001/85/EC, Annex I, paragraph 7.6.1.1. meet the requirements of Table 1. Directive 2001/85/EC, Annex VIII, paragraph 7.6.1.4:for the words “emergency exits” shall be substituted the word “exits”.Vehicles of Class I, II or III: As an alternative to UNECE Regulation 107.02, Annex 3, Paragraph 7.6.1.14 the upper deck gangway shall be connected by one or more intercommunication staircases to the access passageway of a service door or to the lower deck gangway within 3 m of a service door. OrThe technical provisions of UNECE Regulation 107.02 excluding Annex 8.Vehicles of Class I: The technical provisions of UNECE Regulation 107.02, Annex 8. Vehicles of Class A or B: As an alternative to UNECE Regulation 107.02, Annex 3, Paragraph 7.11.3.1 a vehicle may be fitted with handrails or handholds on at least one side and in the case of double doors this requirement may be met by a central stanchion or handrail.In the case of a vehicle of Class III specially designed for the carriage of school children, Annex 3 to UNECE Regulation 107.02 is amended as follows: Vehicles other than Class I: (
  17. a)If fitted with accommodation for a wheelchair the vehicle must comply with the technical provisions of Paragraphs 3.6 and 3.8 of Annex 8 to UNECE Regulation 107.02; (
  18. a)for “225 mm” in Paragraphs 7.7.8.1.1.2 and 7.7.8.1.2.2 substitute “200 mm”; (
  19. b)for “680 mm” in Paragraph 7.7.8.4.1 substitute “650 mm”; and (
  20. c)for “400 mm” in Paragraph 7.7.8.2.2 substitute “350 mm”. Paragraph 7.4 of Annex 3 to UNECE Regulation 107.02 does not apply to: (
  21. a)a vehicle of Class B fitted with no more than 16 passenger seats; or (
  22. b)any other single deck vehicle fitted with a vehicle stability function for which an approval has been issued in accordance with UNECE Regulation 13.11. (
  23. b)If fitted with a boarding aid the vehicle must comply with the technical provisions of Paragraph 3.11 of Annex 8 to UNECE Regulation 107.02. Vehicles of Class A and B: The frontal barrier collision test in 7.6.7.2. of Annex 3 to UNECE Regulation 107.02 does not apply to a vehicle in which all passengers have access to at least two doors, being either a service door or an emergency door, one of which is not a sliding door. UNECE Regulation 107.02, Annex 3, Paragraph 7.6.7.6. In the case of: (
  24. i)a manually operated sliding door fitted with a slam lock of the two stage type, the activation of the device may be by movement of the door itself; (
  25. ii)a nearside rear door forming part of a pair of doors fitted at the rear of the vehicle, the requirements do not apply if that door is capable of being held securely closed by the other door of that pair. Vehicles of Class I, II or III may, as an alternative to the table in UNECE Regulation 107.02, Annex 3, Paragraph 7.6.1.1, meet the requirements of Table 1. The test requirements of Paragraph 3.8. of Annex 8 to UNECE Regulation 107.02 do not apply if the vehicle is designed to meet the strength characteristics equivalent to those needed to satisfy the requirements of those paragraphs. 53. Frontal ImpactIf fitted with airbag, Technical requirements of 96/79/EC Applies to M1 vehicles Component: Approval Installation: Approval / Test Report 54. Side Impact Not Applicable 55. Blank 56. Vehicles Intended for the Transport of Dangerous Goods Not Applicable 57. Front Underrun Protection Not Applicable 58. Pedestrian ProtectionWhere Frontal Protection Systems fitted, the technical provisions of sections 5 and 6 of Annex I to Regulation (EC) 78/2009 Applies to M1 vehiclesApprovals given under superseded Directive 2006/96/EC and the test procedure in Commission Decision 2006/368/EC are acceptable Component: Approval or Test ReportInstallation: Approval or Test Report 59. Recyclability Not Applicable 60. Blank 61. Air-conditioning Systems Not Applicable 62. Hydrogen System The technical provisions and marking requirements of: Regulation (EC) 79/2009 Component: Approval or Test Report Installation: Approval or Test Report 63. General Safety Not Applicable (except as it relates to Subject 46 Tyres) Table 1. Requirement for minimum number of exits in each separate compartment (
  26. a)This table may be used as an alternative to; • Table 7.6.1.1 in Annex 1 of EC Directive 2001/85/EC (
  27. b)and • Table 7.6.1.1 in Annex 3 of UNECE Regulation 107.02 Number of Passengers Number of Service Doors Class I and A Class II Class III and B 9 — 45 1 1 1 46 — 70 2 1 1 71 — 100 2* 2 1 >100 4 3 1 Note * Indicates where the requirement differs from the regulatory acts mentioned above CHAPTER I WHEELCHAIR ACCESSIBILITY REQUIREMENTS Definitions; 1. In this Schedule; “the 1976 Directive” means Council Directive 76/115/EEC (as amended) of 18 December 1975 on the approximation of the laws of the member states relating to anchorages for motor vehicle safety belts; “the 1977 Directive” means Council Directive 77/541/EEC (as amended) of 28 June 1977 on the approximation of the laws of the member states relating to safety belts and restraint systems of motor vehicles; “boarding lift” means a lift fitted to a regulated public service vehicle for the purpose of allowing wheelchair users to board and alight from the vehicle; “boarding ramp” means a ramp fitted to a regulated public service vehicle for the purpose of allowing wheelchair users to board and alight from the vehicle; “contrast” means a contrast in the amount of light which is reflected by the surfaces of the parts of a regulated public service vehicle or its equipment which is required by these Regulations to contrast; “dynamic test” means a test which complies with the requirements of paragraph 3
(7); “exit” means an exit from a regulated public service vehicle but does not include an exit which is provided for use only in case of emergency; “gangway” means the space provided for obtaining access from any entrance to the passengers’ seats or from any such seat to an exit other than an emergency exit, but does not include a staircase or any space in front of a seat or row of seats which is required only for the use of passengers occupying the seat or row of seats; “g” means 9.81 m/s2; “kg” means kilogram(s); “km/h” means kilometre(
  1. s)per hour; “mm” means millimetre(s); “m/s” means metre(
  2. s)per second and “m/s2” means metre(
  3. s)per second per second; “N” means newton(s); “optical device” means any system (including a mirror, closed circuit television and optical cable) which provides the driver of a regulated public service vehicle with a view of an area of the vehicle; “portable ramp” means a ramp which is carried on a regulated public service vehicle for the purpose of allowing wheelchair users to board and alight from the vehicle; “reference wheelchair” means an occupied wheelchair having the dimensions shown in diagram A of Part II to this Schedule; “seat” means a seat intended for use by passengers and, accordingly, does not include the driver’s seat or any other seat intended to use solely by a crew member; “static test” means a test which complies with the requirements of paragraph 3
(5)and which applies the forces specified in paragraph 3
(6); “wheelchair restraint system” means a system which is designed to keep a wheelchair restrained within the wheelchair space; “wheelchair user” means a disabled person using a wheelchair, and “wheelchair user restraint” means a system which is designed to keep a wheelchair user restrained in the wheelchair. Wheelchair spaces 2.
(1)A regulated public service vehicle shall be fitted with not less than one wheelchair space.
(2)Any wheelchair space shall be fitted to the lower deck of a double-deck bus or double-deck coach.
(3)Any wheelchair space on a regulated public service vehicle— (
  1. a)shall comply with the requirements of paragraph 3; or (
  2. b)where the vehicle is adapted to carry standing passengers and is not fitted with any seat belts for passengers which are required to be fitted by regulation, may comply with the requirements of paragraph 4 as an alternative to the requirements of paragraph 3. Forward-facing wheelchairs 3.
(1)Any wheelchair space fitted to a regulated public service vehicle shall comply with the following requirements: (
  1. a)a wheelchair space shall not be less than; (i)1300mm measured in the longitudinal plane of the vehicle; (ii)750mm measured in the transverse plane of the vehicle; and (iii)1500mm measured vertically from any part of the floor of the wheelchair space; (
  2. b)a wheelchair space shall allow the carriage of a wheelchair and a wheelchair user facing the front of the vehicle; (
  3. c)a wheelchair space shall be fitted with a wheelchair restraint system suitable for general wheelchair application; (
  4. d)a wheelchair space shall be fitted with a wheelchair user restraint system which shall comprise a minimum of two anchorage points and a pelvic restraint (lap belt) designed and constructed of components intended to perform in a similar manner to those of a seat belt conforming to the 1977 Directive; (
  5. e)any wheelchair user restraint or wheelchair restraint system fitted to a wheelchair space shall be capable of being easily released in the case of an emergency; (
  6. f)any wheelchair restraint system shall either— (
  7. i)meet the dynamic test requirements described in sub-paragraph
(7)and be securely attached to vehicle anchorages meeting the static test requirements in sub-paragraph
(5); or (ii) be securely attached to vehicle anchorages such that the combination of restraint and anchorages meets the requirements of sub-paragraph
(7)when the anchorages comply with sub-paragraph
(7)(d)(ii); and (
  1. g)any wheelchair user restraint shall either— (
  2. i)meet the test requirements described in sub-paragraph
(8)and be securely attached to vehicle anchorages meeting the static test requirements in sub-paragraph
(5); or (ii) be securely attached to vehicle anchorages such that the combination of restraint and anchorages meets the test requirements described in sub-paragraph
(8)when fitted to a representative section of the vehicle structure as described in sub-paragraph
(5)(g).
(2)One or more seats which are capable of being tipped, folded or otherwise moved may lie within the volume specified in sub-paragraph
(1)(a) or within the gangway specified in paragraph 7 provided that the seat is capable of being easily moved out of the volume or out of the gangway. In the case of a single-deck or double-deck coach, this may include a seat which may be quickly dismantled or removed provided that the seat can be safely stowed.
(3)The clear space in front of any seat may lie within the volume specified in sub-paragraph
(1)(a) or within the gangway specified in paragraph 7.
(4)There shall be a sign on or near a seat specified in sub-paragraphs
(2)and
(3)stating the following “Please give up this seat for a wheelchair user” or stating words of equivalent meaning.
(5)A static test shall be carried out on the anchorage points for both the wheelchair restraint system and the wheelchair user restraint in accordance with the following requirements— (a) the forces specified in sub-paragraph
(6)shall be applied by means of a device reproducing the geometry of the wheelchair restraint system; (b) the forces specified in sub-paragraph
(6)shall be applied by means of a device reproducing the geometry of the wheelchair user restraint and by means of a traction device specified in paragraph 5.3.4 of Annex 1 of the 1976 Directive; (
  1. c)the forces in (
  2. a)and (
  3. b)above shall be applied simultaneously in the forward direction and at an angle of 10°±5° above the horizontal plane; (
  4. d)the forces in (
  5. a)above shall be applied in the rearward direction and at an angle of 10°±5° above the horizontal plane; (
  6. e)the forces shall be applied as rapidly as possible through the central vertical axis of the wheelchair space; (
  7. f)the force shall be maintained for a period of not less than 0.2 seconds; and (
  8. g)the test shall be carried out on a representative section of the vehicle structure together with any fitting provided in the vehicle which is likely to contribute to the strength or rigidity of the structure.
(6)The forces referred to in sub-paragraph
(5)are— (
  1. a)in the case of anchorages provided for a wheelchair restraint system fitted to a Category M2 vehicle— (i)11100N applied in the longitudinal plane of the vehicle and towards the front of the vehicle at a height of not less than 200mm and not more than 300mm measured vertically from the floor of the wheelchair space, and (ii)5500N applied in the longitudinal plane of the vehicle and towards the rear of the vehicle at a height of not less than 200mm and not more than 300mm measured vertically from the floor of the wheelchair space; (
  2. b)in the case of anchorages provided for a wheelchair restraint system fitted to a Category M3 vehicle— (i)7400N applied in the longitudinal plane of the vehicle and towards the front of the vehicle at a height of not less than 200mm and not more than 300mm measured vertically from the floor of the wheelchair space, and (ii)3700N applied in the longitudinal plane of the vehicle and towards the rear of the vehicle at a height of not less than 200mm and not more than 300mm measured vertically from the floor of the wheelchair space; (
  3. c)in the case of anchorages provided for a wheelchair user restraint system, the forces shall be in accordance with the requirements of paragraph 5.4 of Annex 1 of the 1976 Directive; References to M2 and M3 vehicles are references to vehicles of those categories as defined in Annex II (A) to the 1970 Directive.
(7)A wheelchair restraint system shall be subject to a dynamic test carried out in accordance with the following requirements— (
  1. a)a representative wheelchair test trolley of mass 85kg shall, from a speed of between 48km/h to 50km/h to rest, be subject to a deceleration-time pulse in the forward direction which— (
  2. i)exceeds 20g for a cumulative period of at least 0.015 seconds, (
  3. ii)exceeds 15g for a cumulative period of at least 0.04 seconds, (iii) is for an overall duration of at least 0.075 seconds and not more than 0.12 seconds, (
  4. iv)shall not, for a duration of more than 0.08 seconds, be at 28g, and (
  5. v)shall not exceed 28g; (
  6. b)except as provided in (
  7. c)below, a representative wheelchair test trolley of mass 85kg shall, from a speed of between 48km/h to 50km/h to rest, be subject to a deceleration-time pulse in the rearward direction which (
  8. i)exceeds 5g for a cumulative period of at least 0.015 seconds, (
  9. ii)shall not, for a duration of more than 0.02 seconds, be at 8g, and (iii) shall not exceed 8g; (
  10. c)the test in (
  11. b)above shall not apply if the same restraints and direction of loading are used for the forward and rearward direction or if an equivalent test has been conducted; (
  12. d)for the above tests the wheelchair restraint system shall be attached to either— (
  13. i)anchorages fixed to the test rig which represents the geometry of the anchorages in a vehicle for which the restraint system is intended, or (
  14. ii)anchorages forming part of a representative section of the vehicle for which the restraint system is intended, set up as described in sub-paragraph
(5)(g).
(8)A wheelchair occupant restraint shall comply with the test requirements specified in paragraph 2.7.8.4 of Annex 1 of the 1977 Directive or an equivalent test to the deceleration-time pulse in paragraph
(7)(a). A seat belt which has been type approved in accordance with the 1977 Directive, and so marked, shall be deemed to comply.
(9)A test in sub-paragraphs
(5),
(7)or
(8)shall fail unless the following requirements are met— (
  1. a)no part of the system shall have failed, or shall have become detached from its anchorage or from the vehicle during the test; (
  2. b)mechanisms to release the wheelchair and user shall be capable of release after completion of the test; (
  3. c)in the case of the test specified in sub-paragraph
(7), the wheelchair shall not move more than 200mm in the longitudinal plane of the vehicle during the test; and (d) no part of the system shall be deformed to such an extent after completion of the test that, because of sharp edges or other protrusions, the part is capable of causing injury. Rearward-facing wheelchairs 4.
(1)Any wheelchair space fitted to a regulated public service vehicle shall comply with the following requirements— (
  1. a)a wheelchair space shall not be less than— (i)1300mm measured in the longitudinal plane of the vehicle, (ii)750mm measured in the transverse plane of the vehicle, and (iii)1500mm measured vertically from any part of the floor of the wheelchair space; (
  2. b)a wheelchair space shall allow the carriage of a wheelchair and a wheelchair user seated in the wheelchair and facing the rear of the vehicle; (
  3. c)a wheelchair space shall be fitted with a backrest which shall— (
  4. i)be fitted to the front end of the wheelchair space; (
  5. ii)be positioned centrally with respect to the front end of the wheelchair space, and (iii) be fitted with a padded surface facing the rear of the vehicle; and (
  6. d)a wheelchair space shall be fitted with a horizontal handrail which shall— (
  7. i)be fitted along not less than one of the longitudinal sides of the wheelchair space, (
  8. ii)be at a height of not less than 850mm and not more than 1000mm measured vertically from the floor of the wheelchair space, (iii) run continuously from a point not more than 300mm to the rear of the front end of the wheelchair space measured horizontally to a point not less than 1000mm to the rear of the front end of the wheelchair space measured horizontally, (
  9. iv)not extend into the wheelchair space by more than 90mm measured horizontally from the edge of the wheelchair space, (
  10. v)be capable of being easily and firmly gripped by a wheelchair user, (
  11. vi)have a circular cross section with a diameter of not less than 30mm and not more than 35mm, (vii) have clear space of not less than 45mm between any part of the vehicle and all parts of a handrail other than its mountings, (viii) have a slip-resistant surface, and (
  12. ix)contrast with the parts of the vehicle adjacent to the handrail.
(2)Any backrest fitted to a wheelchair space in accordance with sub-paragraph
(1)(
  1. c)shall comply with the following requirements— (
  2. a)the bottom edge of a backrest shall be at a height of not less than 350mm and not more than 480mm measured vertically from the floor of the wheelchair space; (
  3. b)the top edge of a backrest shall be at a height of not less than 1300mm measured vertically from the floor of the wheelchair space; (
  4. c)a backrest shall have a width of— (
  5. i)not less than 270mm and not more than 420mm up to a height of 830mm measured vertically from the floor of the wheelchair space, and (
  6. ii)not less than 270mm and not more than 300mm at heights exceeding 830mm measured vertically from the floor of the wheelchair space; (
  7. d)a backrest shall be fitted at an angle of not less than 4° and not more than 8° to the vertical with the bottom edge of the backrest positioned closer to the rear of the vehicle than the top edge; (
  8. e)the padded surface of a backrest shall form a single and continuous plane; (
  9. f)the padded surface of a backrest shall pass through any point on an imaginary vertical plane situated to the rear of the front end of the wheelchair space and situated not less than 100mm and not more than 120mm from the front end of the wheelchair space measured horizontally and not less than 830mm and not more than 870mm from the floor of the wheelchair space measured vertically; and (
  10. g)a backrest shall be capable of bearing a load of 2000N applied for a minimum of 2 seconds by means of a block 200mm x 200mm square in the longitudinal plane of the vehicle towards the front of the vehicle to the centre of the padded surface of the backrest at a height of not less than 600mm and not more than 800mm measured vertically from the floor of the wheelchair space. The backrest shall not deflect more than 100mm or suffer permanent deformation or damage.
(3)In the lateral plane of the wheelchair space, a clear space of not less than 750mm shall be maintained and, in order to restrict the lateral movement of a reference wheelchair, there shall be a distance not greater than 900mm (measured in the lateral plane of the wheelchair space) between any two of the following adjacent means of support fitted on each side of the wheelchair space— (
  1. a)a vertical stanchion situated to the rear of the front end of the wheelchair space and running continuously from the floor of the wheelchair space to a height of not less than 1500mm, which shall comply with the following requirements— (
  2. i)the base of the stanchion shall be not less than 400mm and not more than 560mm from the front end of the wheelchair space measured horizontally, and (
  3. ii)at heights exceeding 775mm measured vertically from the floor of the wheelchair space, the stanchion shall be not less than 540mm and not more than 560mm from the front end of the wheelchair space measured horizontally; or (
  4. b)a retractable rail extending continuously from a point not more than 200mm from the front end of the wheelchair space to a point not less than 540mm from the front end of the wheelchair space measured horizontally and at a height of not less than 600mm and not more than 800mm measured vertically from the floor of the wheelchair space; or (
  5. c)a partition extending continuously from a point not more than 200mm from the front end of the wheelchair space to a point not less than 540mm from the front end of the wheelchair space measured horizontally and at a height of not less than 600mm and not more than 800mm measured vertically from the floor of the wheelchair space; or (
  6. d)the side wall, or equipment fitted to the side wall, of the vehicle extending continuously from a point not more than 200mm from the front end of the wheelchair space to a point not less than 540mm from the front end of the wheelchair space measured horizontally and at a height of not less than 600mm and not more than 800mm measured vertically from the floor of the wheelchair space.
(4)Any stanchion, retractable rail, partition, or side wall (in this sub-paragraph referred to as “the device”) fitted to a regulated public service vehicle in accordance with sub-paragraph
(3)shall be capable of bearing a load of 1000N applied for a minimum of 2 seconds by means of a block 200mm x 200mm in the transverse plane of the wheelchair space and applied to the centre of the device at a height of not less than 600mm and not more than 800mm measured vertically from the floor of the wheelchair space. The device should not deflect more than 50mm or suffer permanent deformation or damage.
(5)One or more seats which are capable of being tipped, folded or otherwise moved may lie within the volume specified in sub-paragraph
(1)(a) or within the gangway specified in paragraph 7 provided that the seat is capable of being easily moved out of the volume or out of the gangway.
(6)The clear space in front of any seat may lie within the volume specified in sub-paragraph
(1)(a) or within the gangway specified in paragraph 7.
(7)There shall be a sign on or near a seat specified in sub-paragraphs
(5)and
(6)stating the following “Please give up this seat for a wheelchair user” or stating words of equivalent meaning.
(8)In this paragraph, the phrase “front end of a wheelchair space” means the end of a wheelchair space that is closer to the front of the regulated public service vehicle to which the wheelchair space is fitted. Boarding lifts and ramps 5.
(1)A regulated public service vehicle shall be fitted with not less than one boarding lift or one boarding ramp, or shall carry not less than one portable ramp.
(2)Any boarding lift or boarding ramp fitted in accordance with sub-paragraph
(1)shall— (
  1. a)have a safe working load of not less than 300kg; (
  2. b)when subject to a uniformly distributed mass equal to 125 per cent of the safe working load for a period of not less than 10 seconds, not suffer any permanent deformation or damage when the load is removed; (
  3. c)have its maximum safe working load marked in a position which is clearly visible to the operator of the lift or ramp; and (
  4. d)not allow the vehicle in the normal course to be driven away unless the lift or ramp is at its normal position of vehicle travel.
(3)Any boarding ramp fitted to a regulated public service vehicle shall (subject to (
  1. d)below) comply with the following requirements— (
  2. a)a boarding ramp shall have a surface of not less than 800mm in width; (
  3. b)no part of the surface in sub-paragraph
(3)(a), and no part of the vehicle, shall present an obstruction greater than 15mm in height measured along a plane parallel to, and above, the surface of the ramp, and in the direction of travel of a reference wheelchair when moved into or from the vehicle; (c) with the vehicle on a flat surface, in the normal condition for a wheelchair user to board or alight, and with the boarding ramp extended and sitting on a kerb of 125mm in height measured vertically from and parallel to the ground, the surface of a boarding ramp shall have a slope measured over the surface referred to in sub-paragraph
(3)(
  1. a)of not more than [8°] measured relative to the ground; (
  2. d)notwithstanding (
  3. c)above, a boarding ramp may have— (
  4. i)at the intersection of the surface of the kerb and the surface of the ramp described above, a slope not exceeding 15° relative to the ground over a distance of not more than 150mm (measured along the surface of the ramp and parallel to the direction of travel of a reference wheelchair when it is moved from the kerb and onto the ramp surface), and (
  5. ii)at any other point a slope not exceeding 15° relative to the ground over a distance of not more than 150mm (measured along the surface of the ramp and parallel to the direction of travel of a reference wheelchair when it is moved into the vehicle) and rising to a height of not more than 15mm (measured above and parallel to the surface of the ramp or its sections); (
  6. e)with the vehicle on a flat surface and in the normal condition for a wheelchair user to board or alight, the boarding ramp shall be capable of being extended to and of sitting on that surface and in this position the surface of a boarding ramp shall have a slope of not more than 20° measured over the surface referred to in sub-paragraph
(3)(a); (
  1. f)a boarding ramp shall be free of sharp edges or other protrusions capable of causing injury; and (
  2. g)around and abutting each of the edges of a boarding ramp there shall be a band of colour of not less than 50mm in width which shall contrast with the remainder of the ramp surface.
(4)Any boarding lift fitted to a regulated public service vehicle shall comply with the following requirements— (
  1. a)a boarding lift platform shall be not less than 750mm in width and not less than 1200mm in length (excluding the device specified in (
  2. b)below); (
  3. b)unless a boarding lift platform is in the lowered position and resting on a surface from which a wheelchair user will board, the following shall apply— (
  4. i)along any side of the lift platform from which a wheelchair user will move on to, or move from, the lift platform, a device of a height not less than 100mm measured vertically above the surface of the lift platform shall operate automatically as the lift is raised above the lowered position, except that when in the raised position for a wheelchair user to move from the lift platform to the floor of the vehicle, the device shall permit unobstructed access to the floor of the vehicle; (
  5. ii)along any other side, there shall be a device or structure of a height not less than 25mm measured vertically above the surface of the lift platform; and (iii) part of the vehicle structure may fulfil the requirements in (
  6. i)or (
  7. ii)above throughout the operating range of the lift provided that any gaps in the structure are unlikely to cause injury while the lift is in motion; (
  8. c)the vertical operating speed of a boarding lift platform shall not exceed 0.15m/s; (
  9. d)with the vehicle on a flat surface and in the normal condition for a wheelchair user to board or alight, the lift shall be capable of being lowered to and of sitting on that surface; (
  10. e)where the vertical travel of the lift platform exceeds 500mm, at least one side of the lift platform shall be fitted with a handrail where— (
  11. i)in the case of a handrail fitted to the lift platform, a secure horizontal handrail shall be provided at a height of not less than 650mm or more than 1100mm measured vertically from the surface of the lift platform; or (
  12. ii)in the case of a handrail that does not move with the lift platform, a vertical handrail shall provide a grasping point at the same heights above the lift platform throughout the range of the vertical travel; and (
  13. f)around and abutting each of the edges of a boarding lift there shall be a band of colour of not less than 50mm in width which shall contrast with the remainder of the lift surface.
(5)Any power-operated boarding lift or power-operated boarding ramp fitted to a regulated public service vehicle shall (subject to sub-paragraphs
(6)to
(9))— (
  1. a)be capable of operation— (
  2. i)by means of a control situated in the driver’s cab, or (
  3. ii)by means of a control situated adjacent to the lift or ramp which shall only be capable of operation by means of a master control situated in the driver’s cab; (
  4. b)produce an audible signal when in operation; (
  5. c)be capable of being manually operated, or where the vehicle is fitted with more than one lift or ramp, not less than one lift or ramp capable of being manually operated shall be accessible to each wheelchair user; (
  6. d)not be capable of operation when the vehicle is in motion; (
  7. e)be fitted with a safety device which stops the movement of the ramp if the ramp is subject to a reactive force not exceeding 150N in any direction and if that motion could cause injury to a passenger; and (
  8. f)be fitted with sensors capable of stopping the movement of the lift platform if it comes into contact with any thing or person whilst it is in motion and, once stopped, the lift platform must be capable of being reversed.
(6)Sub-paragraph
(5)(f) shall not apply to a power-operated boarding lift which can only be operated by a control fitted in accordance with sub-paragraph
(5)(a)(ii).
(7)As an alternative to the requirement in sub-paragraph
(5)(c), a regulated public service vehicle may carry a portable ramp.
(8)This sub-paragraph applies where— (
  1. a)a power-operated boarding lift is fitted to a regulated public service vehicle, and (
  2. b)there are areas of that lift which are not visible to a person operating the lift.
(9)Where sub-paragraph
(8)applies— (
  1. a)the lift shall be fitted with a stop control which is within easy reach of any user of the lift and which is operable with the palm of the hand, and (
  2. b)where the stop control is activated, the lift, once stopped, shall be capable of being reversed.
(10)Where a portable ramp is carried in a regulated public service vehicle the ramp shall— (
  1. a)not easily be moved when it is in the normal position for a wheelchair user to board or alight from the vehicle and it is being so used; (
  2. b)be provided with a stowage position in a position where it is readily available for use; (
  3. c)be capable of being securely stowed in the stowing position so as to minimise the risk of injury to the passengers, the driver and any other crew members; and (
  4. d)comply with the requirements in sub-paragraph
(2)(a), (
  1. b)and (
  2. c)and
(3)as if references to “boarding ramp” were references to “portable ramp”.
(11)In this paragraph “master control” means a control which enables another control to activate the relevant system, but which is not itself alone capable of activating that system. Entrances and exits 6.
(1)Any entrance or exit which is intended to provide access for a wheelchair user shall have a clear unobstructed width of not less than 800mm.
(2)Subject to sub-paragraph
(3), where an entrance or exit which is intended to provide access for a wheelchair user is fitted with a power-operated boarding lift or a power-operated boarding ramp which is not within the direct field of vision of the driver— (
  1. a)the entrance or exit shall be fitted with an optical device; and (
  2. b)the optical device shall enable the driver to have a clear unobstructed view of the inside and outside of the door area and of the operation of the lift or ramp.
(3)Sub-paragraph
(2)shall not apply to a power-operated boarding lift or a power-operated ramp which can only be operated by a control fitted in accordance with paragraph 5
(5)(a)(ii). Gangways 7. Any gangway between a wheelchair space and an entrance or exit intended to provide access for a wheelchair user— (
  1. a)shall allow a reference wheelchair to be moved from an entrance to the wheelchair space and from the wheelchair space to an exit, with the wheelchair user moving in a forward facing direction, and to be moved (in either direction) from the gangway into the wheelchair space in the appropriate direction for travel; (
  2. b)shall not be less than 750mm wide at any point along the gangway; and (
  3. c)where a vehicle is fitted with more than one wheelchair space, the requirement in (
  4. a)above shall be met with any other wheelchair space occupied with a reference wheelchair. Signs and markings 8.
(1)A regulated public service vehicle shall have a sign conforming with diagram B in Part II of this Schedule, or a sign of equivalent meaning conforming to the dimensions in that diagram, which is; (
  1. a)coloured white on a blue background, (
  2. b)of dimensions of not less than 150mm by 150mm when fitted externally or of not less than 60mm by 60mm when fitted internally, and (
  3. c)situated— (
  4. i)on the exterior of the vehicle and adjacent to any entrance for a wheelchair user, (
  5. ii)on the interior of the vehicle and adjacent to any exit for a wheelchair user, and (iii) adjacent to any wheelchair space, and in a position clearly visible to a wheelchair user.
(2)There shall be situated adjacent to a wheelchair space and in a position clearly visible to a wheelchair user— (
  1. a)a sign indicating the direction that the wheelchair and the wheelchair user shall face during travel, and (
  2. b)appropriate safety instructions explaining the use of the wheelchair space.
(3)Where a regulated public service vehicle is fitted with a wheelchair space for a forward facing wheelchair in accordance with the requirements of paragraph 3, instructions on the use of the wheelchair restraint system and wheelchair user restraint shall be situated in a position readily visible to any person using the system. Communication devices 9.
(1)A communication device shall be fitted to a regulated public service vehicle in the following positions— (
  1. a)adjacent to a wheelchair space and in a position readily useable by any person who is using the wheelchair space, and (
  2. b)on the exterior of the vehicle adjacent to any entrance for wheelchair access which is outside the direct view of the driver, except where that entrance is in the rear of the vehicle in which case the device shall be fitted on the rearmost part of the side face of the vehicle from which passengers will board the vehicle and at a height of not less than 850mm and not more than 1000mm measured vertically from the ground (with the vehicle at its minimum height if it is fitted with a kneeling system) to the centre of the device.
(2)Unless sub-paragraph
(3)applies, any communication device fitted in accordance with sub-paragraph
(1)shall comply with the following requirements— (
  1. a)a communication device shall be operable by the palm of the hand; (
  2. b)the surround of the communication device shall contrast with the device and with the surface on which the surround is mounted; and (
  3. c)when operated, a communication device shall activate an audible signal which enables the driver to identify that a device fitted in accordance with sub-paragraph
(1)has been activated, and where fitted in accordance with sub-paragraph
(1)(a), after activating an audible signal may (on being operated subsequently) provide a visual signal which is visible to the driver until the opening of at least one of the exits.
(3)Where a regulated public service vehicle is required to comply with Schedule 2, any communication device fitted in accordance with sub-paragraph
(1)(
  1. a)shall comply with the following requirements— (
  2. a)a communication device shall be operable by the palm of the hand; (
  3. b)the surround of the communication device shall contrast with the device and with the surface on which the surround is mounted; and (
  4. c)when operated, a communication device— (
  5. i)after activating an audible signal to the driver which enables the driver to identify that a device fitted in accordance with sub-paragraph
(1)(
  1. a)or (
  2. b)has been activated, may (on being operated subsequently) provide a visual signal to the driver until the opening of at least one of the exits; (
  3. ii)shall activate an audible signal which is audible in the passenger area; and (iii) shall activate at least one illuminated stopping sign on each deck of the vehicle or, in the case of an articulated vehicle, on each section of that vehicle, which is or would be within the field of vision of the passengers seated on a majority of the seats on that deck or in that section.
(4)An illuminated stopping sign— (
  1. a)shall not use only capital letters; and (
  2. b)shall display illuminated the word “stopping” or a word or words to that effect immediately a communication device is activated and until at least one of the exits is open. Lighting 10.
(1)Lighting shall be fitted to illuminate the interior and exterior of a regulated public service vehicle sufficient to allow a wheelchair user to board and alight from the vehicle in safety.
(2)Any lighting fitted to a regulated public service vehicle in accordance with sub-paragraph
(1)shall have a means of preventing its operation when the vehicle is in motion if its use is likely to affect adversely the driver’s vision. Diagram A-Wheelchair Dimensions Diagram B-Wheelchair Sign CHAPTER II GENERAL ACCESSIBILITY REQUIREMENTS FOR SINGLE-DECK AND DOUBLE-DECK BUSES (Class I) Definitions 1. In this Schedule; “contrast” means a contrast in the amount of light which is reflected by the surfaces of the parts of a regulated public service vehicle or its equipment which is required by these Regulations to contrast; “cushion” means that part of a seat on which a person using the seat sits, whether padded or not; “deep” in relation to a step, means the distance from the outer edge of the nosing of the step tread to the riser of the step tread; “doorway area” means that area which is within one metre of any entrance or exit measured horizontally from any point along the external edge of the door aperture; “exit” means an exit from a regulated public service vehicle but does not include an exit which is provided for use only in case of emergency; “external step” means the last step or platform from an entrance or an exit which lea

🔗 To official source

AI explanation based on the official legal text. Indicative, not a substitute for legal advice.