← Polska

Konwencja o kontroli i cechowaniu wyrobów z metali szlachetnych, sporządzona w Wiedniu dnia 15 listopada 1972 r.

Dziennik Ustaw Nr 46 — 2986 — Poz. 297 297 KONWENCJA o kontroli i cechowaniu wyrobów z metali szlachetnych, sporzàdzona w Wiedniu dnia 15 listopada 1972 r. W imieniu Rzeczypospolitej Polskiej PREZYDENT RZECZYPOSPOLITEJ POLSKIEJ podaje do powszechnej wiadomoÊci: W dniu 15 listopada 1972 r. zosta∏a sporzàdzona w Wiedniu Konwencja o kontroli i cechowaniu wyrobów z metali szlachetnych, w nast´pujàcym brzmieniu: Przek∏ad KONWENCJA CONVENTION CONVENTION o kontroli i cechowaniu wyrobów z metali szlachetnych on the control and marking of articles of precious metals sur le controle et le poin˜onnement des ouvrages en métaux précieux Preambu∏a Preamble Préambule Republika Austrii, Republika Finlandii, Królestwo Norwegii, Republika Portugalska, Królestwo Szwecji, Konfederacja Szwajcarska oraz Zjednoczone Królestwo Wielkiej Brytanii i Irlandii Pó∏nocnej, The Republic of Austria, the Republic of Finland, the Kingdom of Norway, the Portuguese Republic, the Kingdom of Sweden, the Swiss Confederation and the United Kingdom of Great Britain and Northern Ireland; La République d’Autriche, la République de Finlande, le Royaume de Norv¯ge, la République Portugaise, le Royaume de Su¯de, la Confédération Suisse et le Royaume-Uni de Grande-Bretagne et d’Irlande du Nord, pragnàc u∏atwiç mi´dzynarodowy handel wyrobami z metali szlachetnych i jednoczeÊnie zapewniç ochron´ konsumenta, wymaganà ze wzgl´du na szczególny charakter tych wyrobów, Desiring to facilitate international trade in articles of precious metals while at the same time maintaining consumer protection justified by the particular nature of these articles; Désireux de faciliter le commerce international des ouvrages en métaux précieux tout en assurant la protection du consommateur justifiée par la nature particuli¯re de ces ouvrages, uzgodni∏y, co nast´puje: Have agreed as follows: Sont convenus de ce qui suit: I. Zakres i oddzia∏ywanie I. Scope and operation I. Portée et fonctionnement de la Convention Artyku∏ 1 Article 1 Article 1 1. Wyroby z metali szlachetnych, importowane z terytorium innego Umawiajàcego si´ Paƒstwa poddane kontroli i ocechowane zgodnie z postanowieniami niniejszej konwencji — sà uwa˝ane za zgodne z przepisami prawnymi danego Umawiajàcego si´ Paƒstwa, wymagajàcymi badania tych wyrobów przez upowa˝niony urzàd oraz w∏aÊciwego cechowania ich urz´dowymi znakami, aby mo˝na by∏o stwierdziç, ˝e zosta∏y one dostatecznie zbadane lub wymagajàcymi cechowania takich wyrobów, aby mo˝na by∏o stwierdziç ich wytwórc´, rodzaj metalu lub okreÊlonà prób´. 1. Legal provisions of a Contracting State which require articles of precious metals to be assayed by an authorized body and to be marked with official stamps so as to indicate that they have been satisfactorily assayed, or require such articles to be marked so as to indicate the sponsor, the nature of the metal or the standard of fineness, shall be deemed to be satisfied in respect of articles of precious metals imported from the territory of anther Contracting State if such articles have been controlled and marked in accordance with the provisions of this Convention. 1. Les dispositions légales d’un Etat Contractant prescrivant que les ouvrages en métaux précieux doivent ˘tre contrôlés par une instance autorisée et marqués des poin˜ons officiels attestant que les essais effectués sont satisfaisants ou prescrivant que ces ouvrages soient munis des poin˜ons indiquant le responsable, le genre de métal ou le titre, seront réputées observées pour ce qui est des ouvrages en métaux précieux importés du territoire d’un autre Etat Contractant, si ces ouvrages ont été contrôlés et poin˜onnés conformément aux dispositions de la présente Convention. Dziennik Ustaw Nr 46 — 2987 — Poz. 297 2. W przypadku wyrobów kontrolowanych i cechowanych zgodnie z postanowieniami niniejszej konwencji, importujàce Umawiajàce si´ Paƒstwo nie b´dzie wymaga∏o dalszego badania ani cechowania w sensie okreÊlonym w ust´pie 1, poza testami kontrolnymi, o których mowa w artykule 6. 2. For articles controlled and marked in accordance with the provisions of this Convention an importing Contracting State shall not require further assaying or marking of a kind referred to in paragraph 1, except for the purpose of check tests as provided in Article 6. 2. Un Etat Contractant d’importation n’exigera pas pour les ouvrages contrôlés et poin˜onnés confor-mément aux dispositions de la pré-sente Convention un nouveau con-trôle ou poin˜onnement de la nature de celui mentionné au paragraphe 1, si ce n’est ∫ des fins d’essai par épreuve au sens de l’article 6. 3. ˚adne z postanowieƒ niniejszej konwencji nie wymaga od Umawiajàcych si´ Paƒstw dopuszczenia do importu lub sprzeda˝y wyrobów z metali szlachetnych, które nie spe∏niajà paƒstwowych minimalnych norm dotyczàcych próby. Ponadto, ˝adne z postanowieƒ niniejszej konwencji nie wymaga od Umawiajàcych si´ Paƒstw, które akceptujà 800 jako prób´ srebra, by dopuszcza∏y do importu lub sprzeda˝y wyroby oznaczone próbà 830. 3. Nothing in this Convention shall require a Contracting State to allow the importation or sale of articles of precious metals which do not fulfil its national minimum standards of fineness. Furthermore, nothing in this Convention shall require a Contracting State which accepts 800 as a standard of fineness for silver to allow the importation or sale of articles marked with the 830 standard of fineness. 3. Aucune disposition de la présente Convention n’oblige un Etat Contractant ∫ autoriser l’importation ou la vente d’ouvrages en métaux précieux qui ne satisfont pas aux titres minimums nationaux. En outre, aucune disposition de la présente Convention n’oblige un Etat Contractant qui admet l’argent au titre de 800 ∫ autoriser l’importation ou la vente d’ouvrages d’argent marqués au titre de 830. Artyku∏ 2 Article 2 Article 2 Dla celów niniejszej konwencji okreÊlenie „wyroby z metali szlachetnych” oznacza wyroby ze srebra, z∏ota, platyny i ich stopów — zgodnie z definicjà, która zawarta jest w za∏àczniku I. For the purposes of this Convention ”articles of precious metals” means articles of silver, gold, platinum or alloys thereof, as defined in Annex I. Aux fins de la présente Convention, on entend par „ouvrages en métaux précieux” les ouvrages en argent, en or, en platine ou en alliages de ces métaux tels qu’ils sont définis ∫ l’Annexe I. Artyku∏ 3 Article 3 Article 3 1. Aby korzystaç z postanowieƒ artyku∏u 1, wyroby z metali szlachetnych muszà byç: 1. In order to benefit from the provisions of Article 1, articles of precious metals must be: 1. Pour ˘tre admis au bénéfice des dispositions de l’article 1, les ouvrages en métaux précieux doivent ˘tre: (

  1. a)zg∏oszone do upowa˝nionego urz´du probierczego wyznaczonego zgodnie z artyku∏em 5; (
  2. a)submitted to an authorized assay office appointed in accordance with Article 5;
  3. a)soumis ∫ un bureau de contrôle des métaux précieux reconnu, désigné conformément ∫ l’article 5; (
  4. b)poddane kontroli przez upowa˝niony urzàd probierczy zgodnie z zasadami i procedurami okreÊlonymi w za∏àcznikach I i II; (
  5. b)controlled by the authorized assay office in accordance with the rules and procedures laid down in Annexes I and II;
  6. b)contrôlés par le bureau de contrôle des métaux précieux reconnu selon les r¯gles et procédés fixés aux Annexes I et II; (
  7. c)ocechowane znakami, okreÊlonymi w za∏àczniku II, a tak˝e Wspólnà Cechà Kontroli, opisanà w ust´pie 8 tego za∏àcznika. (
  8. c)marked with the marks as prescribed in Annex II, including the Common Control Mark as described in paragraph 8 thereof.
  9. c)munis des poin˜ons prescrits ∫ l’Annexe II, y compris le Poin˜on Commun qui est décrit au paragraphe 8 de cette Annexe. 2. KorzyÊci wynikajàce z artyku∏u 1 nie b´dà mia∏y zastosowania do wyrobów z metali szlachetnych, na których — po ocechowaniu zgodnie z za∏àcznikiem II — znaki zosta∏y zmienione lub zatarte. 2. The benefits of Article 1 shall not be applicable to articles of precious metals which, after being marked as prescribed in Annex II, have had any of these marks altered or obliterated. 2. Ne bénéficient pas des dispositions de l’article 1 les ouvrages en métaux précieux dont l’un des poin˜ons, apr¯s avoir été apposé conformément ∫ l’Annexe II, a été modifié ou oblitéré. Dziennik Ustaw Nr 46 — 2988 — Poz. 297 Artyku∏ 4 Article 4 Article 4 Umawiajàce si´ Paƒstwa nie b´dà mia∏y obowiàzku stosowaç postanowieƒ ust´pów 1 i 2 artyku∏u 1 do wyrobów z metali szlachetnych, które — po zg∏oszeniu do upowa˝nionego urz´du probierczego, poddaniu kontroli i ocechowaniu zgodnie z artyku∏em 3 — zosta∏y zmienione przez domieszki lub w jakikolwiek inny sposób. The Contracting States shall not be obliged to apply the provisions of paragraphs 1 and 2 of Article 1 to articles of precious metals which, since being submitted to an authorized assay office, and controlled and marked as prescribed in Article 3, have been altered by addition or in any other manner. Les Etats Contractants ne sont pas tenus d’appliquer les dispositions des paragraphes 1 et 2 de l’article 1 aux ouvrages en métaux précieux qui, apr¯s avoir été soumis ∫ un bereau de contrôle des métaux précieux reconnu, contrôlés et poin˜onnés conformément ∫ l’article 3, ont été modifiés par adjonction de parties supplémentaires ou de toute autre mani¯re. II. Kontrola i sankcje II. Control and sanctions II. Contrôle et sanctions Artyku∏ 5 Article 5 Article 5 1. Ka˝de Umawiajàce si´ Paƒstwo wyznaczy jeden lub wi´kszà liczb´ urz´dów probierczych, które b´dà jedynymi urz´dami upowa˝nionymi na jego terytorium do przeprowadzania kontroli wyrobów z metali szlachetnych, przewidzianej w niniejszej konwencji oraz do stosowania swojego w∏asnego znaku wyznaczonego urz´du probierczego i Wspólnej Cechy Kontroli. 1. Each Contracting State shall appoint one or more assay offices which shall be the only bodies authorized in its territory to carry out the control of articles of precious metals provided for in this Convention and to apply its own appointed assay office mark and the Common Control Mark. 1. Chaque Etat Contractant désigne un ou plusieurs bureaux de contrôle des métaux précieux qui seront les seuls établissements de son territoire habilités ∫ effectuer le contrôle des ouvrages en métaux précieux prévu aux termes de la présente Convention et ∫ apposer leur propre poin˜on de contrôle et le Poin˜on Commun. 2. Ka˝de Umawiajàce si´ Paƒstwo powiadomi depozytariusza o wyznaczeniu takiego upowa˝nionego urz´du probierczego i o jego znakach, a tak˝e o ka˝dym cofni´ciu upowa˝nienia wczeÊniej wyznaczonemu urz´dowi probierczemu. Skutkiem tego depozytariusz niezw∏ocznie odpowiednio powiadomi pozosta∏e Umawiajàce si´ Paƒstwa. 2. Each Contracting State shall notify the depositary of the appointment of such authorized assay offices and of their assay office marks and any withdrawal of this authorization from any assay office previously appointed. The depositary shall immediately notify all other Contracting States accordingly. 2. Chaque Etat Contractant notife ∫ l’Etat dépositaire les bureaux de contrôle des métaux précieux reconnus qu’il a désignés, leurs poin˜ons de contrôle et, le cas échéant, le retrait de l’agrément donné ∫ tout bureau désigné antérieurement. L’Etat dépositaire en donne immédiatement notification ∫ tous les autres Etats Contractants. Artyku∏ 6 Article 6 Article 6 Postanowienia niniejszej konwencji nie b´dà uniemo˝liwia∏y Umawiajàcym si´ Paƒstwom przeprowadzania badaƒ kontrolnych wyrobów z metali szlachetnych, opatrzonych znakami przewidzianymi w niniejszej konwencji. Badania takie nie b´dà prowadzone w sposób nadmiernie zak∏ócajàcy import i sprzeda˝ wyrobów z metali szlachetnych ocechowanych zgodnie z postanowieniami niniejszej konwencji. The provisions of this Convention shall not prevent a Contracting State from carrying out check tests on articles of precious metals bearing the marks provided for in this Convention. Such tests shall not be carried out in such a way as to hamper unduly the importation or sale of articles of precious metals marked in conformity with the provisions of this Convention. Les dispositions de la présente Convention n’emp˘chent pas un Etat Contractant d’effectuer des essais par épreuve sur les ouvrages en métaux précieux portant les poin˜ons prévus dans la présente Convention. Ces essais ne devront pas ˘tre effectués de mani¯re ∫ g˘ner indûment l’importation ou la vente des articles en métaux précieux poin˜onnés conformément aux dispositions de la Convention. Artyku∏ 7 Article 7 Article 7 Umawiajàce si´ Paƒstwa upowa˝niajà niniejszym depozytariusza do zarejestrowania Wspólnej Cechy Kontroli w Âwiatowej Organizacji W∏asnoÊci Intelektualnej The Contracting States hereby empower the depositary to register with the World Intellectual Property Organization (WIPO), in accordance with the Convention of Par la présente Convention, les Etats Contractants autorisent l’Etat dépositaire ∫ enregistrer le Poin˜on Commun en qualité de poin˜on national de chaque Etat Con- Dziennik Ustaw Nr 46 — 2989 — Poz. 297 (WIPO), zgodnie z Konwencjà paryskà o ochronie w∏asnoÊci przemys∏owej — jako paƒstwowego stempla probierczego ka˝dego Umawiajàcego si´ Paƒstwa. Depozytariusz dokona takiej rejestracji równie˝ w odniesieniu do Umawiajàcego si´ Paƒstwa, dla którego niniejsza konwencja wejdzie w ˝ycie w póêniejszym terminie, a tak˝e w odniesieniu do paƒstw przyst´pujàcych do niniejszej konwencji. Paris for the Protection of Industrial Property, the Common Control Mark as a national hallmark of each Contracting State. The depositary shall also do so in the case of a Contracting State in relation to which this Convention enters into force at a later date or in the case of an acceding State. tractant aupr¯s de l’Organisation Mondiale de la Propriété Intellectuelle (OMPI), conformément ∫ la Convention de Paris pour la protection de la propriété industrielle. L’Etat dépositaire procédera de m˘me en ce qui concerne un Etat Contractant pour lequel la présente Convention entrera en vigueur ∫ une date postérieure ou dans le cas d’un Etat adhérent. Artyku∏ 8 Article 8 Article 8 1. Ka˝de Umawiajàce si´ Paƒstwo w∏àczy do swojego ustawodawstwa uregulowania prawne, przewidujàce kary za fa∏szerstwa i nadu˝ywanie Wspólnej Cechy Kontroli, ustanowionej niniejszà konwencjà, oraz cech upowa˝nionych urz´dów probierczych, zg∏oszonych zgodnie z ust´pem 2 artyku∏u 5, a tak˝e za wprowadzanie — bez upowa˝nienia — zmian w wyrobach i za zmienianie lub zacieranie próby i znaków wytwórcy po wykonaniu ocechowania wyrobu Wspólnà Cechà Kontroli. 1. Each Contracting State shall have and maintain legislation prohibiting, subject to penalties, any forgery or misuse of the Common Control Mark provided for by this Convention or of the marks of the authorized assay offices which have been notified in accordance with paragraph 2 of Article 5, and any unauthorized alteration to the article or alteration or obliteration of the fineness mark or responsibility mark after the Common Control Mark has been applied. 1. Chaque Etat Contractant doit avoir et maintenir une législation interdisant, sous peine de sanctions, toute contrefa˜on ou tout usage abusif du Poin˜on Commun prévu par la présente Convention ou des poin˜ons des bureaux de contrôle des métaux précieux reconnus dont notification a été donnée conformément au paragraphe 2 de l’article 5, ainsi que toute modification non autorisée apportée ∫ l’ouvrage ou toute modification ou oblitération de l’indication du titre ou du poin˜on de responsabilité, une fois que le Poin˜on Commun a été apposé. 2. Ka˝de Umawiajàce si´ Paƒstwo zobowiàzuje si´ ustanowiç — w ramach tych uregulowaƒ prawnych — stosowne post´powanie w przypadkach stwierdzenia lub uzyskania od innego Umawiajàcego si´ Paƒstwa dostatecznych dowodów fa∏szerstwa albo nadu˝ycia Wspólnej Cechy Kontroli lub cech upowa˝nionych urz´dów probierczych, albo te˝ dowodów wprowadzenia — bez upowa˝nienia — zmian w wyrobie lub zmiany albo zatarcia próby lub znaku wytwórcy po wykonaniu ocechowania Wspólnà Cechà Kontroli, a gdzie b´dzie to w∏aÊciwsze — zobowiàzujà si´ podjàç inne stosowne dzia∏ania. 2. Each Contracting State undertakes to institute proceedings under such legislation when sufficient evidence of forgery or misuse of the Common Control Mark or marks of the authorized assay offices, or unauthorized alteration to the article or alteration or obliteration of the fineness mark or responsibility mark after the Common Control Mark has been applied is discovered or brought to its attention by another Contracting State or, where more appropriate, to take other suitable action. 2. Chaque Etat Contractant engagera des poursuites en application de ladite législation lorsqu’une preuve suffisante est établie ou portée ∫ sa connaissance par un autre Etat Contractant de la contrefa˜on ou de l’usage abusif du Poin˜on Commun ou des poin˜ons des bureaux de contrôle reconnus ou encore d’une modification non autorisée apportée ∫ l’ouvrage ou d’une modification ou oblitération de l’indication du titre ou du poin˜on de responsabilité, une fois que le Poin˜on Commun a été apposé. Lorsque cela est plus approprié, d’autres mesures adéquates peuvent ˘tre prises. Artyku∏ 9 Article 9 Article 9 1. Je˝eli którekolwiek z Umawiajàcych si´ Paƒstw b´dàce importerem lub którykolwiek z jego urz´dów probierczych b´dà mia∏y powód, by twierdziç, ˝e urzàd probierczy Umawiajàcego si´ Paƒstwa b´dàcego eksporterem, opatrzy∏ wyrób Wspólnà Cechà Kontroli bez zastosowania si´ do odnoÊnych postanowieƒ niniejszej konwencji, bezzw∏ocznie podj´te zostanà roz- 1. If an importing Contracting State or one of its assay offices has reason to believe that an assay office of an exporting Contracting State has affixed the Common Control Mark without having complied with the relevant provisions of this Convention, the assay office by which the articles are purported to have been marked shall be immediately consulted, and the latter 1. Lorsqu’un Etat Contractant d’importation ou l’un de ses bureaux de contrôle des métaux précieux a des raisons de croire qu’un bureau de contrôle des métaux précieux d’un Etat Contractant d’exportation a apposé le Poin˜on Commun sans se conformer aux dispositions y relatives de la présente Convention, le bureau de contrôle censé avoir procédé au Dziennik Ustaw Nr 46 — 2990 — Poz. 297 mowy z urz´dem probierczym, który, wed∏ug domniemywaƒ, dokona∏ takiego ocechowania wyrobów, a urzàd ten udzieli wszelkiej nale˝ytej pomocy w celu zbadania tej sprawy. Je˝eli nie zostanie osiàgni´te zadowalajàce rozwiàzanie, ka˝da ze stron b´dzie mia∏a prawo zwróciç si´ z tà sprawà do Sta∏ego Komitetu drogà powiadomienia jego przewodniczàcego. W takim przypadku przewodniczàcy zwo∏a posiedzenie Sta∏ego Komitetu nie póêniej ni˝ w ciàgu jednego miesiàca od daty otrzymania takiego powiadomienia. assay office shall promptly lend all reasonable assistance for the investigation of the case. If no satisfactory settlement is reached, either of the parties may refer the case to the Standing Committee by notifying its Chairman. In such a case the Chairman shall convene a meeting of the Standing Committee not later than one month from the receipt of such notification. poin˜onnement des ouvrages sera immédiatement consulté et il fournira sans tarder toute l’assistance qui convient aux fins d’une investigation du cas. Si aucun arrangement satisfaisant n’intervient, l’une ou l’autre partie peut soumettre le cas au Comité permanent par notification adressée ∫ son président. En l’occurrence, le Comité permanent se réunira sur convocation du président au plus tard un mois apr¯s réception de ladite notification. 2. Je˝eli do Sta∏ego Komitetu wp∏ynie jakakolwiek sprawa zwiàzana z postanowieniami ust´pu 1, Sta∏y Komitet mo˝e — po wys∏uchaniu zainteresowanych stron — wydaç zalecenia w celu podj´cia w∏aÊciwych dzia∏aƒ. 2. If any matter has been referred to the Standing Committee under paragraph 1, the Standing Committee may, after having given an opportunity for the parties concerned to be heard, make recommendations as to the appropriate action to be taken. 2. Lorsqu’un cas a été porté devant le Comité permanent en vertu du paragraphe 1, celui-ci, apr¯s avoir donné aux parties intéressées la possibilité d’˘tre entendues, peut présenter des recommandations sur les mesures appropriées∫ ∫ prendre. 3. Je˝eli zalecenie, o którym mowa w ust´pie 2, nie zostanie wykonane w mo˝liwym do przyj´cia czasie lub je˝eli Sta∏y Komitet nie wyda ˝adnego zalecenia, Umawiajàce si´ Paƒstwo b´dàce importerem mo˝e wprowadziç nad cechowanymi przez dany urzàd probierczy i wprowadzanymi na terytorium tego paƒstwa wyrobami z metali szlachetnych dodatkowy nadzór, który uzna za konieczny, ∏àcznie z prawem czasowej odmowy przyjmowania takich wyrobów. O podj´ciu takich Êrodków bezzw∏ocznie zostanà powiadomione wszystkie Umawiajàce si´ Paƒstwa, a realizacja tych Êrodków b´dzie od czasu do czasu rozpatrywana przez Sta∏y Komitet. 3. If within a reasonable time a recommendation referred to in paragraph 2 has not been complied with, or the Standing Committee has failed to make any recommendation, the importing Contracting State may then introduce such additional surveillance of articles of precious metals marked by that particular assay office and entering its territory, as it considers necessary, including the right temporarily to refuse to accept such articles. Such measures shall immediately be notified to all Contracting States and shall be reviewed from time to time by the Standing Committee. 3. Si, dans un délai raisonnable, une recommandation au sens du paragraphe 2, n’a pas été observée ou si le Comité permanent n’a pas pu adopter de recommandation, l’Etat Contractant d’importation peut alors introduire les mesures de surveillance supplémentaire qu’il juge nécessaires ∫ l’égard des ouvrages en métaux précieux poin˜onnés par le bureau de contrôle en question et qui entrent sur son territoire; il a aussi le droit de ne pas accepter temporairement de tels ouvrages. Ces mesures seront notifiées immédiatement ∫ tous les Etats Contractants et seront revues périodiquement par la Comité permanent. 4. Gdy b´dà istnia∏y dowody powtarzajàcego si´ i powa˝nego nadu˝ywania Wspólnej Cechy Kontroli, Umawiajàce si´ Paƒstwo b´dàce importerem mo˝e czasowo odmówiç przyjmowania wyrobów opatrzonych znakiem probierczym danego urz´du probierczego, niezale˝nie od tego, czy zosta∏y one poddane kontroli i ocechowane zgodnie z niniejszà konwencjà. W takim przypadku Umawiajàce si´ Paƒstwo b´dàce importerem niezw∏ocznie powiadomi o tym wszystkie pozosta∏e Umawiajàce si´ Paƒstwa, a Sta∏y Komitet zbierze si´ w terminie jednego miesiàca w celu rozpatrzenia tej sprawy. 4. Where there is evidence of repeated and grave misapplication of the Common Control Mark the importing Contracting State may temporarily refuse to accept articles bearing the assay office mark of the assay office concerned whether or not controlled and marked in accordance with this Convention. In such a case the importing Contracting State shall immediately notify all other Contracting States and the Standling Committee shall meet within one month to consider the matter. 4. Lorsqu’il existe des preuves d’une utilisation abusive répétée et grave du Poin˜on Commun, l’Etat Contractant d’importation peut temporairement refuser d’accepter les ouvrages portant le poin˜on de contrôle du bureau en cause, que ceux-ci soient ou non contrôlés et poin˜onnés conformément ∫ la présente Convention. En pareil cas, l’Etat Contractant d’importation avisera immédiatement tous les autres Etats Contractants et le Comité permanent se réunira dans l’intervalle d’un mois pour examiner la question. Dziennik Ustaw Nr 46 — 2991 — Poz. 297 III. Sta∏y Komitet i poprawki III. Standing Committee and amendments III. Comité permanent et amendements Artyku∏ 10 Article 10 Article 10 1. Niniejszym ustanowiony zostaje Sta∏y Komitet, w którym reprezentowane b´dzie ka˝de Umawiajàce si´ Paƒstwo. Ka˝de Umawiajàce si´ Paƒstwo b´dzie posiadaç jeden g∏os. 1. A Standing Committee is hereby established on which each Contracting State shall be represented. Each Contracting State shall have one vote. 1. Par la présente Convention, il est créé un Comité permanent dans lequel chaque Etat Contractant est représenté et y dispose d’une voix. 2. Sta∏y Komitet b´dzie mia∏ nast´pujàce zadania: 2. The tasks of the Standing Committee shall be: 2. Le Comité permanent aura les attributions suivantes: rozpatrywanie i przeglàd oddzia∏ywania niniejszej konwencji; to consider and review the operation of this Convention; étudier et revoir le fonctionnement de la Convention; rozwijanie wspó∏pracy technicznej i administracyjnej mi´dzy Umawiajàcymi si´ Paƒstwami w sprawach obj´tych niniejszà konwencjà; to promote technical and administrative co-operation between the Contracting States in matters dealt with by this Convention; encourager la coopération technique et administrative entre les Etats Contractants dans les domaines relevant de la présente Convention; rozpatrywanie Êrodków zapewniajàcych jednakowà interpretacj´ i stosowanie postanowieƒ niniejszej konwencji; to consider measures for securing uniform interpretation and application of the provisions of this Convention; étudier les mesures permettant d’assurer une interprétation et une application uniformes des dispositions de la présente Convention; wspieranie stosownej ochrony znaków przed ich fa∏szowaniem i nadu˝ywaniem; to encourage the adequate protection of the marks against forgery and misuse; encourager une protection adéquate des poin˜ons contre la contrefa˜on et l’usage abusif; wydawanie zaleceƒ w przypadkach zaistnienia spraw uj´tych w postanowieniach ust´pu 2 artyku∏u 9 lub w celu rozstrzygni´cia wszelkich sporów, wynikajàcych z oddzia∏ywania niniejszej konwencji, zg∏oszonych do Sta∏ego Komitetu; to make recommendations in the case of any matter referred to it under the provisions of paragraph 2 of Article 9, or for the settlement of any dispute arising out of the operation of this Convention which is presented to the Standing Committee; présenter des recommandations sur chaque cas qui lui est soumis en vertu des dispositions du paragraphe 2 de l’article 9 ou pour le r¯glement de tout différend survenant dans l’application de la présente Convention et qui est soumis au Comité permanent; badanie, czy uregulowania istniejàce w paƒstwie zainteresowanym przystàpieniem do konwencji spe∏niajà wymagania niniejszej konwencji i jej za∏àczników, oraz sporzàdzanie raportów w tej sprawie w celu ich rozwa˝enia przez Umawiajàce si´ Paƒstwa. to examine whether the arrangements of a State interested in acceding to this Convention comply with the conditions of the Convention and its Annexes and to make a report in that respect for consideration by the Contracting States. examiner si les arrangements d’un Etat désirant adhérer ∫ la présente Convention satisfont aux exigences de la Convention et de ses annexes et présenter un rapport ∫ ce sujet ∫ l’attention des Etats Contractants. 3. Sta∏y Komitet przyjmie zasady proceduralne dotyczàce swoich posiedzeƒ, ∏àcznie z zasadami zwo∏ywania takich posiedzeƒ. Niniejszy Komitet b´dzie zbiera∏ si´ co najmniej raz w roku. Pierwsze jego posiedzenie zostanie zwo∏ane przez depozytariusza nie póêniej ni˝ w ciàgu szeÊciu miesi´cy od daty wejÊcia w ˝ycie niniejszej konwencji. 3. The Standing Committee shall adopt rules of procedure for its meeting including rules for the convening of such meetings. This Committee shall meet at least once a year. The first meeting shall be convened by the depositary not later than six months after the coming into force of this Convention. 3. Le Comité permanent adoptera des r¯gles de procédure régissant ses réunions y compris des r¯gles de convocation. Il se réunira au moins une fois par an. La premi¯re réunion aura lieu sur convocation de l’Etat dépositaire six mois au plus tard apr¯s l’entrée en vigueur de la présente Convention. 4. Sta∏y Komitet mo˝e wydawaç zalecenia dotyczàce ka˝dej sprawy zwiàzanej z wdro˝eniem niniejszej konwencji lub proponowaç poprawki do niniejszej kon- 4. The Standing Committee may make recommendations on any question relating to the implementation of this Convention or make proposals for the amend- 4. Le Comité permanent peut présenter des recommandations sur toute question en relation avec la mise en oeuvre de la présente Convention ou faire des proposi- Dziennik Ustaw Nr 46 — 2992 — Poz. 297 wencji i jej za∏àczników. Takie zalecenia lub propozycje b´dà przedstawiane depozytariuszowi, który powiadomi o nich wszystkie Umawiajàce si´ Paƒstwa. ment of this Convention or its Annexes. Such recommendations or proposals shall be transmitted to the depositary who shall notify all Contracting States. tions d’amendement de la Convention ou de ses annexes. Ces recommandations ou propositions seront transmises ∫ l’Etat dépositaire qui en donnera notification ∫ tous les Etats Contractants. Artyku∏ 11 Article 11 Article 11 1. W przypadku otrzymania od Sta∏ego Komitetu propozycji poprawki do za∏àczników do niniejszej konwencji, depozytariusz powiadomi o niej wszystkie Umawiajàce si´ Paƒstwa i zwróci si´ do ich rzàdów o wyra˝enie — w terminie czterech miesi´cy — zgody na wprowadzenie proponowanej poprawki. Zgoda ta mo˝e mieç charakter warunkowy, tak by mo˝na by∏o uwzgl´dniç wewn´trzne wymagania konstytucyjne. 1. In the case of a proposal received from the Standing Committee for amendment of the Annexes to the Convention the depositary shall notify all Contracting States and invite their Governments to give their consent to the proposed amendment within four months. Such consent may be conditional in order to meet internal constitutional requirements. 1. Si l’Etat dépositaire re˜oit du Comité permanent une proposition d’amendements des annexes de la Convention, il en donne notification ∫ tous les Etats Contractants et invite leurs gouvernements ∫ donner leur approbation ∫ l’amendement proposé dans un délai de quatre mois. Cette approbation peut ˘tre conditionnelle, afin de satisfaire aux exigences constitutionnelles nationales. 2. O ile w terminie okreÊlonym w ust´pie 1 nie wp∏ynie negatywna odpowiedê od rzàdu któregokolwiek z Umawiajàcych si´ Paƒstw, poprawka do za∏àczników wejdzie w ˝ycie po szeÊciu miesiàcach po up∏ywie tego terminu, o ile dana poprawka nie b´dzie przewidywa∏a póêniejszej daty wejÊcia w ˝ycie, oraz z zastrze˝eniem, ˝e zostanà spe∏nione warunki okreÊlajàce zgod´, o której mowa w ust´pie 1. Depozytariusz powiadomi wszystkie Umawiajàce si´ Paƒstwa o wejÊciu w ˝ycie poprawki i zwiàzanej z tym dacie. 2. Unless a negative reply has been received from the Government of a Contracting State within the period mentioned in paragraph 1, the amendment to the Annexes shall come into force six months after the expiration of this period unless a later date for its entry into force has been provided for in the amendment, and provided that the conditions in any consent referred to in paragraph 1 have been fulfilled. The depositary shall notify the entry into force and the relevant date to all Contracting States. 2. A moins d’une réponse négative re˜ue du gouvernement d’un Etat Contractant dans le délai indiqué au paragraphe 1, l’amendement aux annexes entrera en vigueur six mois apr¯s expiration dudit délai, sauf si une date postérieure d’entrée en vigueur est prévue dans l’amendement et sous réserve que les conditions d’approbation auxquelles se réf¯re le paragraphe 1 aient été remplies dans chaque cas. L’Etat dépositaire notifiera ∫ tous les Etats Contractants l’entrée en vigueur de l’amendement et la date applicable. 3. W przypadku otrzymania od Sta∏ego Komitetu propozycji poprawki do artyku∏ów niniejszej konwencji lub w przypadku propozycji poprawki do konwencji lub do jej za∏àczników, zg∏oszonej przez którekolwiek z Umawiajàcych si´ Paƒstw, depozytariusz przed∏o˝y do akceptacji te propozycje wszystkim Umawiajàcym si´ Paƒstwom. 3. In the case of a proposal received from the Standing Committee for the amendment of the Articles to the Convention, or in the case of a proposal for amendment of the Convention or its Annexes received from a Contracting State, the depositary shall submit such proposals for acceptance to all Contracting States. 3. Si l’Etat dépositaire re˜oit du Comité permanent une proposition d’amendement des articles de la Convention ou d’un Etat Contractant une proposition d’amendement de la Convention ou de ses annexes, il soumettra ces propositions ∫ l’acceptation de tous les Etats Contractants. 4. Je˝eli w ciàgu trzech miesi´cy od daty przed∏o˝enia propozycji poprawki zg∏oszonej zgodnie z ust´pem 3, którekolwiek z Umawiajàcych si´ Paƒstw za˝àda podj´cia negocjacji na temat takiej poprawki, depozytariusz umo˝liwi przeprowadzenie takich negocjacji. 4. If within three months from the date of the submission of a proposal for amendment under paragraph 3 a Contracting State requests that negotiations be opened on the proposal, the depositary shall arrange for such negotiations to be held. 4. Si dans les trois mois ∫ compter de la date ∫ laquelle une proposition d’amendement a été soumise conformément au paragraphe 3, un Etat Contractant demande l’ouverture de négociations sur ladite proposition, l’Etat dépositaire prend les dispositions nécessaires ∫ cet effet. 5. Je˝eli proponowana zgodnie z ust´pem 3 poprawka do konwencji lub do jej za∏àczników zostanie przyj´ta przez wszystkie Umawiajàce si´ Paƒstwa, to wejdzie ona 5. Provided it is accepted by all Contracting States, an amendment to this Convention or its Annexes proposed under paragraph 3 shall enter into force on month after de- 5. Sous réserve de son acceptation par tous les Etats Contractants, un amendement ∫ la présente Convention ou ∫ ses annexes proposé conformément au para- Dziennik Ustaw Nr 46 — 2993 — Poz. 297 w ˝ycie po up∏ywie jednego miesiàca od daty z∏o˝enia ostatniego dokumentu przyj´cia, o ile poprawka nie przewiduje innej daty wejÊcia w ˝ycie. Dokumenty przyj´cia sk∏adane b´dà u depozytariusza, który powiadomi wszystkie Umawiajàce si´ Paƒstwa. posit of the last instrument of acceptance unless another date is provided for in the amendment. Instruments of acceptance shall be deposited with the depositary who shall notify all Contracting States. graphe 3 entrera en vigueur un mois apr¯s le dépôt du dernier instrument d’acceptation, ∫ moins qu’une autre date ne soit prévue dans l’amendement. Les instruments d’acceptation seront déposés aupr¯s de l’Etat dépositaire qui en donnera notification ∫ tous les Etats Contractants. IV. Postanowienia koƒcowe IV. Final provisions IV. Dispositions finales Artyku∏ 12 Article 12 Article 12 1. Do niniejszej konwencji mo˝e przystàpiç — po otrzymaniu zaproszenia od Umawiajàcych si´ Paƒstw, przekazanego przez rzàd depozytariusza — ka˝de paƒstwo b´dàce cz∏onkiem Organizacji Narodów Zjednoczonych lub jakiejkolwiek jej wyspecjalizowanej agendy, albo b´dàce cz∏onkiem Mi´dzynarodowej Agencji Energii Atomowej lub stronà Statutu Mi´dzynarodowego Trybuna∏u SprawiedliwoÊci i posiadajàce uregulowania w zakresie badania i cechowania wyrobów z metali szlachetnych, niezb´dne do spe∏nienia wymogów niniejszej konwencji i jej za∏àczników. 1. Any State being a Member of the United Nations or of any of the specialized agencies or of the International Atomic Energy Agency or a Party to the Statute of the International Court of Justice and having arrangements for the assay and marking of articles of precious metals necessary to comply with the requirements of the Convention and its Annexes may, upon invitation of the Contracting States to be transmitted by the depositary government, accede to this Convention. 1. Tout Etat membre de l’Organisation des Nations Unies ou membre d’une institution spécialisée ou de l’Agence internationale de l’énergie atomique ou partie au Statut de la Cour internationale de Justice disposant des arrangements pour le contrôle et le poin˜onnement des ouvrages en métaux précieux nécessaires pour se conformer aux exigences de la présente Convention et de ses annexes peut, sur l’invitation des Etats Contractants qui sera transmise par le Gouvernement dépositaire, adhérer ∫ la présente Convention. 2. Podejmujàc decyzj´ o zaproszeniu jakiegoÊ paƒstwa do przystàpienia do konwencji, rzàdy Umawiajàcych si´ Paƒstw b´dà opieraç si´ przede wszystkim na raporcie, o którym mowa w ust´pie 2 artyku∏u 10. 2. The Governments of the Contracting States shall base their decision whether to invite a State to accede primarily on the report referred to in paragraph 2 of Article 10. 2. Les gouvernements des Etats Contractants, pour décider d’inviter un Etat ∫ adhérer, se fonderont essentiellement sur le rapport qui est mentionné au paragraphe 2 de l’article 10. 3. Paƒstwo, które otrzyma zaproszenie, mo˝e przystàpiç do niniejszej konwencji, sk∏adajàc swój dokument przystàpienia u depozytariusza, który powiadomi o tym wszystkie Umawiajàce si´ Paƒstwa. Przystàpienie nabierze mocy prawnej po up∏ywie trzech miesi´cy od daty z∏o˝enia tego dokumentu. 3. The invited State may accede to this Convention by depositing an instrument of accession with the depositary which shall notify all other Contracting States. The accession shall become effective three months after deposit of that instrument. 3. L’Etat invité peut adhérer ∫ la présente Convention en déposant son instrument d’adhésion aupr¯s de l’Etat dépositaire qui en donne notification ∫ tous les autres Etats Contractants. L’adhésion déploiera ses effets trois mois apr¯s le dépôt de cet instrument. Artyku∏ 13 Article 13 Article 13 Królestwo Danii i Republika Islandii, które bra∏y udzia∏ w opracowywaniu projektu niniejszej konwencji, mogà przystàpiç do niej, sk∏adajàc dokument przystàpienia u depozytariusza. Przystàpienie nabierze mocy prawnej po up∏ywie dwóch miesi´cy od daty z∏o˝enia tego dokumentu, lecz nie wczeÊniej ni˝ po up∏ywie okresu czterech miesi´cy, o którym mowa w ust´pie 2 artyku∏u 16. The Kingdom of Denmark and the Republic of Iceland, which participated in the drafting of this Convention, may accede to it by depositing an instrument of accession with the depositary. The accession shall become effective two months after the date of deposit of that instrument, but not before the expiry of the period of four months mentioned in paragraph 2 of Article 16. Le Royaume de Danemark et la République d’Islande, qui ont participé ∫ l’élaboration de la présente Convention, peuvent y adhérer en déposant un instrument d’adhésion aupr¯s de l’Etat dépositaire. L’adhésion devient effective deux mois apr¯s la date du dépôt de cet instrument, mais pas avant l’expiration de la période de’ quatre mois mentionnée au paragraphe 2 de l’article 16. Dziennik Ustaw Nr 46 — 2994 — Poz. 297 Artyku∏ 14 Article 14 Article 14 1. Rzàd paƒstwa — sygnatariusza lub paƒstwa przyst´pujàcego do konwencji mo˝e — w momencie z∏o˝enia swojego dokumentu ratyfikacyjnego lub przystàpienia lub w dowolnym póêniejszym terminie — z∏o˝yç u depozytariusza pisemne oÊwiadczenie, ˝e niniejsza konwencja b´dzie mia∏a zastosowanie do wszystkich lub do cz´Êci — okreÊlonych w oÊwiadczeniu — terytoriów, za których stosunki zewn´trzne dany rzàd jest odpowiedzialny. Depozytariusz przeka˝e ka˝de takie oÊwiadczenie rzàdom wszystkich pozosta∏ych Umawiajàcych si´ Paƒstw. 1. The Government of any signatory or acceding State may, when depositing its instrument of ratification or accession, or at any time thereafter, declare in writing to the depositary that this Convention shall apply to all or part of the territories, designated in the declaration, for the external relations of which it is responsible. The depositary shall communicate any such declaration to the Governments of all other Contracting States. 1. Le gouvernement de tout Etat signataire ou adhérent peut, lors du dépôt de son instrument de ratification ou d’adhésion ou, par la suite, ∫ n’importe quel moment, présenter une déclaration écrite ∫ l’Etat dépositaire selon laquelle la présente Convention s’applique ∫ tout ou partie des territoires, désignés dans ladite déclaration, pour lesquels il assure les relations extérieures. Une telle déclaration sera communiquée par l’Etat dépositaire aux gouvernements de tous les autres Etats Contractants. 2. Je˝eli oÊwiadczenie zosta∏o z∏o˝one w momencie z∏o˝enia dokumentu ratyfikacyjnego lub przystàpienia, to w stosunku do tych terytoriów niniejsza konwencja wejdzie w ˝ycie w tym samym dniu, w którym wejdzie w ˝ycie w stosunku do paƒstwa, które z∏o˝y∏o to oÊwiadczenie. We wszystkich innych przypadkach konwencja wejdzie w ˝ycie w sprawach tych terytoriów po trzech miesiàcach od daty otrzymania oÊwiadczenia przez depozytariusza. 2. If the declaration was made at the time of the deposit of the instrument of ratification or accession this Convention shall enter into force in relation to those territories on the same date as the Convention enters into force in relation to the State having made the declaration. In all other cases the Convention shall enter into force in relation to those territories three months after the declaration has been received by the depositary. 2. Si cette déclaration a été faite au moment du dépôt de l’instrument de ratification ou d’adhésion, la présente Convention entrera en vigueur en ce qui concerne ces territoires ∫ la m˘me date que la Convention entre en vigueur pour l’Etat qui a présenté la déclaration. Dans tous les autres cas, la Convention entrera en vigueur pour ces territoires trois mois apr¯s réception de la déclaration par l’Etat dépositaire. 3. Stosowanie niniejszej konwencji do wszystkich takich terytoriów lub do cz´Êci z nich mo˝e zostaç zakoƒczone przez rzàd paƒstwa, który z∏o˝y∏ oÊwiadczenie, o którym mowa w ust´pie 1, pod warunkiem ˝e z trzymiesi´cznym wyprzedzeniem w pisemnej formie zawiadomi on o tym depozytariusza, który powiadomi wszystkie pozosta∏e Umawiajàce si´ Paƒstwa. 3. The application of this Convention to all or part of such territories may be terminated by the Government of the State having made the declaration referred to in paragraph 1 provided that it gives three months’ notice in writing to the depositary which shall notify all other Contracting States. 3. L’application de la présente Convention ∫ tout ou partie des territoires en question peut ˘tre dénoncée par le gouvernement de l’Etat qui a présenté la déclaration mentionnée au paragraphe 1 moyennant un préavis écrit de trois mois ∫ l’Etat dépositaire qui en donnera notification ∫ tous les autres Etats Contractants. Artyku∏ 15 Article 15 Article 15 Ka˝de Umawiajàce si´ Paƒstwo mo˝e wypowiedzieç niniejszà konwencj´ pod warunkiem, ˝e z dwunastomiesi´cznym wyprzedzeniem w pisemnej formie zawiadomi o tym depozytariusza, który powiadomi wszystkie Umawiajàce si´ Paƒstwa lub na innych warunkach, które zostanà uzgodnione przez Umawiajàce si´ Paƒstwa. Wszystkie Umawiajàce si´ Paƒstwa zobowiàzujà si´, ˝e w przypadku wypowiedzenia konwencji, nie b´dà wykorzystywaç po wypowiedzeniu Wspólnej Cechy Kontroli do ˝adnych celów. Any Contracting State may withdraw from this Convention provided that it gives twelve months’ notice in writing to the depositary who shall notify all Contracting States, or on such other terms as may be agreed upon by the Contracting States. Each Contracting State undertakes that, in the event of its withdrawal from the Convention, it will cease after withdrawal to use or apply the Common Control Mark for any purpose. Tout Etat Contractant peut se retirer de la présente Convention moyennant un préavis écrit de douze mois ∫ l’Etat dépositaire qui en donnera notification ∫ tous les Etats Contractants, ou ∫ toutes autres conditions dont seront convenus les Etats Contractants. Chaque Etat Contractant s’engage, au cas où il se retirerait de la Convention, ∫ cesser, d¯s qu’il se sera retiré, toute utilisation ou application du Poin˜on Commun pour n’importe quel usage. Dziennik Ustaw Nr 46 — 2995 — Poz. 297 Artyku∏ 16 Article 16 Article 16 1. Niniejsza konwencja zostanie ratyfikowana przez paƒstwa, b´dàce jej sygnatariuszami. Dokumenty ratyfikacyjne zostanà z∏o˝one u depozytariusza, który powiadomi o tym wszystkie pozosta∏e paƒstwa b´dàce sygnatariuszami niniejszej konwencji. 1. This Convention shall be ratified by the signatory States. The instruments of ratification shall be deposited with the depositary which shall notify all other signatory States. 1. La présente Convention doit ˘tre ratifiée par les Etats signataires. Les instruments de ratification seront déposés aupr¯s de l’Etat dépositaire qui en donnera notification ∫ tous les autres Etats signataires. 2. Niniejsza konwencja wejdzie w ˝ycie po up∏ywie czterech miesi´cy od daty z∏o˝enia czwartego dokumentu ratyfikacyjnego. W stosunku do wszystkich pozosta∏ych paƒstw — sygnatariuszy, które z∏o˝à swoje dokumenty ratyfikacyjne w dalszej kolejnoÊci, niniejsza konwencja wejdzie w ˝ycie po up∏ywie dwóch miesi´cy od daty z∏o˝enia dokumentu ratyfikacyjnego, lecz nie wczeÊniej ni˝ po up∏ywie okresu czterech miesi´cy, o którym mowa wy˝ej. 2. This Convention shall enter into force four months after deposit of the fourth instrument of ratification. In relation to any other signatory State depositing subsequently its instrument of ratification this Convention shall enter into force two months after the date of deposit but not before the expiry of the above-mentioned period of four months. 2. La présente Convention entrera en vigueur quatre mois apr¯s le dépôt du quatri¯me instrument de ratification. En ce qui concerne tout autre Etat signataire qui déposera son instrument de ratification ultérieurement, la présente Convention entrera en vigueur deux mois apr¯s la date du dépôt mais pas avant l’expiration de la période de quatre mois susmentionnée. NA DOWÓD CZEGO ni˝ej podpisani, nale˝ycie w tym celu upowa˝nieni, podpisali niniejszà konwencj´. IN WITNESS WHEREOF the undersigned, duly authorized thereto, have signed the present Convention. EN FOI de quoi, les soussignés, dûment autorisés ∫ cet effet, ont signé la présente Convention. SPORZÑDZONO w Wiedniu dnia pi´tnastego listopada 1972 r., po jednym egzemplarzu w j´zykach angielskim i francuskim, przy czym oba teksty sà jednakowo autentyczne, które zostanà z∏o˝one Rzàdowi Szwecji, który przeka˝e uwierzytelnione kopie wszystkim pozosta∏ym paƒstwom — sygnatariuszom i przyst´pujàcym do konwencji. DONE at Vienna this 15th day of November 1972, in a single copy in the English and French languages, both texts being equally authentic, which shall be deposited with the Government of Sweden, by which certified copies shall be transmitted to all other signatory and acceding States. FAIT ∫ Vienne le 15 novembre 1972, en fran˜ais et en anglais, les deux textes faisant également foi, en un seul exemplaire qui sera déposé aupr¯s du Gouvernement de la Su¯de qui en transmettra copie certifiée conforme ∫ tous les autres Etats signataires et adhérents. Za∏àcznik I Annex I Annexe I DEFINICJE I WYMAGANIA TECHNICZNE DEFINITIONS AND TECHNICAL REQUIREMENTS DÉFINITIONS ET EXIGENCES TECHNIQUES 1. Dla celów niniejszej konwencji wyroby z metali szlachetnych oznaczajà wyroby, które wykonane sà ze z∏ota, srebra, platyny lub ich stopów lub te˝ zawierajàce te metale i stopy oraz których wszystkie cz´Êci metalowe sà wykoƒczone, z wy∏àczeniem: 1. For the purposes of this Convention articles of precious metals means articles consisting of or containing gold, silver, platinum or their alloys and complete as to all their metallic parts, but excluding the following: 1. Sont réputés ouvrages en métaux précieux aux fins de la présente Convention les ouvrages enti¯rement ou partiellement en or, en argent, en platine ou en un alliage de ces métaux et qui comportent toutes leurs parties métalliques, ∫ l’exclusion toutefois: (
  10. a)wyrobów wykonanych ze stopów o próbie ni˝szej ni˝ 375 w przypadku z∏ota, o próbie ni˝szej ni˝ 800 w przypadku srebra i ni˝szej ni˝ 950 w przypadku platyny; (
  11. a)articles consisting of alloys of a fineness less than 375 for gold, 800 for silver or 950 for platinum;
  12. a)des ouvrages faits d’un alliage dont le titre est inférieur ∫ 375 pour l’or, 800 pour l’argent et 950 pour le platine; (
  13. b)cz´Êci i niewykoƒczonych pó∏fabrykatów; (
  14. b)parts or incomplete semi-manufactures;
  15. b)des parties d’ouvrages ou desproduits semi-ouvrés incomplets; (
  16. c)surowców, do których zaliczane sà sztabki, p∏ytki, arkusze, folie, pr´ty, druty, taÊmy i rurki. (
  17. c)raw materials including bars, plates, sheets, foils, rods, wire, strips and tubes.
  18. c)des mati¯res premi¯res y compris les barres, plaques, feuilles, lames, baguettes, fils, bandes et tubes. Dziennik Ustaw Nr 46 — 2996 — Poz. 297 OkreÊlone próby Standards of fineness Titres 2. Dla celów niniejszej konwencji rozró˝nia si´ nast´pujàce próby: 2. The following standards of fineness shall be recognized for the purpose of this Convention: 2. Aux fins de la présente Convention les titres suivants sont reconnus: (
  19. a)dla z∏ota: 750, 585 i 375; (
  20. a)for gold, 750, 585 and 375;
  21. a)750, 585 et 375 pour l’or, (
  22. b)dla srebra: 925, 830 i 800; (
  23. b)for silver, 925, 830 and 800;
  24. b)925, 830 et 800 pour l’argent, (
  25. c)dla platyny: 950. (
  26. c)for platinum, 950.
  27. c)950 pour le platine. 3. „Próba” oznacza liczb´ wagowych cz´Êci z∏ota, srebra lub platyny na 1 000 wagowych cz´Êci stopu. 3. ”Fineness” means the number of parts by weight of fine gold of silver or platinum in 1,000 parts by weight of alloy. 3. Le „titre” est la proportion en poids d’or fin, d’argent fin ou de platine fin contenue dans 1 000 parties d’un alliage. 4. Dla celów niniejszej konwencji uwa˝a si´, ˝e okreÊlona próba wyrobu z metalu szlachetnego o próbie wy˝szej ni˝ norma dla danego metalu, ustalona w ust´pie 2, odpowiada najbli˝szej ni˝szej normie ustalonej w tym ust´pie. 4. The standard of fineness of any article of precious metal, which is of a fineness higher than a standard for that metal mentioned in paragraph 2 shall for the purposes of this Convention be regarded as being of the nearest lower standard as defined in that paragraph. 4. Si le titre d’un ouvrage en métal précieux est supérieur ∫ l’un des titres énumérés au paragraphe 2, l’ouvrage sera considéré, aux fins de la présente Convention, comme étant au titre immédiatement inférieur indiqué audit paragraphe. 5. Próba wszystkich cz´Êci wyrobu, z wy∏àczeniem stopu lutowniczego i takich cz´Êci, które sà dopuszczalne na mocy ust´pów 7—14, nie b´dzie ni˝sza ni˝ okreÊlona próba dla danego wyrobu. 5. The fineness of all parts of the article, excluding solder and such parts as are permitted under paragraphs 7 to 14, shall be not less than the standard of fineness for the article concerned. 5. Aucune partie d’un ouvrage en métal précieux ne sera ∫ un titre inférieur ∫ celui de l’ouvrage, ∫ l’exception de la soudure et des parties admises en vertu des paragraphes 7 ∫ 14. Stosowanie stopu lutowniczego The use of solder Usage de la soudure 6. OkreÊlone próby stopu lutowniczego b´dà nast´pujàce: 6. Standards of fineness of solder shall be as follows: 6. Les titres admis pour les soudures sont les suivants: (
  28. a)Z∏oto. Stop lutowniczy u˝ywany do wyrobów ze z∏ota b´dzie mia∏ takà samà prób´, jak dany wyrób, z nast´pujàcymi wyjàtkami: (
  29. a)Gold. The solder for gold articles shall be of the same standard of fineness as the article concerned, subject to the following exceptions:
  30. a)Or. La soudure des ouvrages d’or sera au m˘me titre que ceux-ci, sous réserve des exceptions suivantes: W przypadku wyrobów ze z∏ota filigranowej roboty i kopert do zegarków o próbie 750 stop lutowniczy b´dzie zawiera∏ nie mniej ni˝ 740 cz´Êci z∏ota na 1 000. Dla wyrobów z bia∏ego z∏ota o próbie 750 stop lutowniczy b´dzie zawiera∏ nie mniej ni˝ 585 cz´Êci z∏ota na 1 000. In the case of gold articles of filigree work and watch cases of the 750 standard, the solder shall contain not less than 740 parts of gold per 1,000. For white gold articles of the 750 standard the solder shall contain not less than 585 parts of gold per 1,000. Pour les ouvrages d’or en filigrane et les boîtes de montre, au titre de 750, la soudure contiendra au moins 740 milli¯mes d’or. Pour les ouvrages en or blanc au titre de 750, la soudure contiendra au moins 585 milli¯mes d’or. (
  31. b)Srebro. Stop lutowniczy u˝ywany do wyrobów ze srebra o próbie 925 b´dzie zawiera∏ nie mniej ni˝ 650 cz´Êci srebra na 1 000. Stop lutowniczy dla wyrobów ze srebra o próbach 800 i 830 b´dzie zawiera∏ nie mniej ni˝ 550 cz´Êci srebra na 1 000. (
  32. b)Silver. Solder for silver articles of the 925 standard shall contain not less than 650 parts of silver per 1,000. Solder for silver articles of the 800 and 830 standards shall contain not less than 550 parts of silver per 1,000.
  33. b)Argent. Pour les ouvrages en argent au titre de 925, la soudure contiendra au moins 650 milli¯mes d’argent. Pour les ouvrages en argent aux titres de 800 et 830, la soudure contiendra au moins 550 milli¯mes d’argent. (
  34. c)Platyna. Stop lutowniczy dla platyny b´dzie zawiera∏ co najmniej 995 cz´Êci z∏ota, srebra, platyny lub palladu na 1 000. (
  35. c)Platinum. Solder for platinum shall contain at least 995 parts per 1,000 of gold, silver, platinum or palladium.
  36. c)Platine. La soudure pour le platine contiendra au moins 995 milli¯mes d’or, d’argent, de platine ou de palladium. Dziennik Ustaw Nr 46 — 2997 — Poz. 297 Stop lutowniczy, który ma ni˝szà prób´ ni˝ wyrób, b´dzie stosowany tylko w iloÊciach niezb´dnych do po∏àczenia elementów. Taki stop lutowniczy nie b´dzie stosowany do wzmacniania, obcià˝ania i wype∏niania. Solder which is below the standard of fineness of the article shall be used only in the quantities necessary for joining. Such solder shall not be used for strengthening, weighting or filling. La soudure dont le titre est inférieur ∫ celui de l’ouvrage ne sera utilisée qu’en quantités nécessaires au soudage. Elle ne doit pas ˘tre utilisée pour renforcer, alourdir ou bourrer un ouvrage. Stosowanie cz´Êci z metali nieszlachetnych The use of base metal parts Usage de parties en métal commun 7. Stosowanie cz´Êci z metali nieszlachetnych w wyrobach z metali szlachetnych b´dzie zabronione z nast´pujàcymi wyjàtkami: 7. Base metal parts in precious metal articles shall be prohibited except as follows: 7. Les ouvrages en métaux précieux ne doivent pas comporter des parties en métal commun, sous réserve des exceptions suivantes: (
  37. a)mechanizmów w o∏ówkach automatycznych, zegarach i zegarkach, wewn´trznych mechanizmów zapalniczek i innych tego rodzaju mechanizmów, gdzie z przyczyn technicznych stosowanie metali szlachetnych nie jest wskazane; (
  38. a)movements of propelling pencils, clocks and watches, the internal mechanism of lighters and similar mechanisms where precious metals are unsuitable for technical reasons;
  39. a)mécanismes de porte-mine, mouvements d’horlogerie, mécanismes internes des briquets et mécanismes similaires où l’usage des métaux précieux n’est pas approprié pour des raisons d’ordre technique; (
  40. b)ostrzy no˝y oraz takich cz´Êci otwieraczy do butelek, korkociàgów i innych tego rodzaju wyrobów, które z przyczyn technicznych nie mogà byç wykonane z metali szlachetnych; (
  41. b)blades of knives and such parts of bottle openers and corkscrews and similar articles which for technical reasons cannot be made of precious metals;
  42. b)lames de couteau et parties de décapsuleurs, tire-bouchons et objets similaires qui, pour des raisons d’ordre technique, ne peuvent ˘tre confectionnés en métaux précieux; (
  43. c)spr´˝yn; (
  44. c)springs;
  45. c)ressorts; (
  46. d)drutu do po∏àczeƒ w srebrnych zawiasach; (
  47. d)wire for joints of silver hinges;
  48. d)goupilles de charni¯res en argent; (
  49. e)zapi´ç w broszkach ze srebra. (
  50. e)pins for silver brooches.
  51. e)épingles de broches en argent. 8. Cz´Êci z metali nieszlachetnych, dopuszczalne zgodnie z ust´pami 7(a), (c), (
  52. d)i (
  53. e)nie b´dà przylutowywane do metalu szlachetnego. 8. Base metal parts permitted under paragraph 7(a), (c), (
  54. d)and (
  55. e)shall not be soldered to the precious metal. 8. Les parties en métal commun admises au sens du paragraphe 7 a), c),
  56. d)et
  57. e)ne doivent pas ¯tre soudées au métal précieux. 9. Na cz´Êciach nieszlachetnych wsz´dzie tam, gdzie to jest mo˝liwe, b´dzie odciÊni´te lub wygrawerowane s∏owo „METAL”, z konkretnym okreÊleniem tego metalu; natomiast tam, gdzie nie jest to mo˝liwe, cz´Êci te powinny byç ∏atwo odró˝nialne od metalu szlachetnego po kolorze. Wymaganie to nie ma zastosowania do mechanizmów zegarów i zegarków. Metale nieszlachetne nie b´dà stosowane jedynie do celów wzmacniania, obcià˝ania i wype∏niania. 9. Base metal parts where practicable shall be stamped or engraved ”METAL”or with a specific designation of the metal; where this is impracticable these shall be readily distinguishable by colour from the precious metal. This requirement shall not apply to clock or watch movements. Base metal shall not be used merely for strengthening, weighting or filling purposes. 9. Les parties en métal commun doivent porter le mot „METAL“ ou une désignation spécifique du métal insculpé ou gravé; si un tel marquage est irréalisable, ces parties devront se distinguer facilement du métal précieux par leur couleur. Cette exigence ne s’applique pas aux mouvements d’horlogerie. Le métal commun ne doit pas ˘tre utilisé simplement pour renforcer, alourdir ou bourrer un ouvrage. Stosowanie substancji niemetalowych The use of non-metallic substances Usage de mati¯res non métalliques 10. Stosowanie cz´Êci niemetalowych jest dozwolone pod warunkiem, ˝e b´dà one wyraênie odró˝nia∏y si´ od metalu szlachetnego, nie b´dà powlekane ani malowane w sposób imitujàcy metale szla- 10. The use of non-metallic parts shall be permitted provided these are clearly distinguishable from the precious metal, they are not plated or coloured to resemble precious metals and their extent is 10. L’usage de parties non métalliques est autorisé ∫ condition que celles-ci se distinguent clairement du métal précieux; ces mati¯res ne doivent pas ˘tre plaquées ou colorées de fa˜on ∫ ressembler Dziennik Ustaw Nr 46 — 2998 — Poz. 297 chetne, a ich kontury b´dà dobrze widoczne. Niemetalowe wype∏nienia uchwytów no˝y, widelców i ∏y˝ek b´dà równie˝ dozwolone, pod warunkiem ˝e wype∏nienia te b´dà stosowane tylko w takich iloÊciach, jakie sà niezb´dne dla ∏àczenia elementów. clearly visible. Non-metallic fillings for handles for knives, forks and spoons shall also be permitted provided such fillings are used only in the quantities that are necessary for joining. aux métaux précieux et seront nettement visibles. Le bourrage des manches de couteaux, de fourchettes ou de cuill¯res en mati¯res non métalliques est également autorisé ∫ condition que ces mati¯res ne soient utilisées qu’en quantités nécessaires ∫ fixer le manche. Stosowanie wi´cej ni˝ jednego metalu szlachetnego w jednym wyrobie The use of more than one precious metal in the same article Usage de plusieurs métaux précieux dans le m˘me ouvrage 11. Stosowanie wi´cej ni˝ jednego metalu szlachetnego w jednym wyrobie jest zabronione z wyjàtkiem nast´pujàcych przypadków: 11. The use of more than one precious metal in the same article shall be prohibited except in the following cases: 11. Il est interdit d’utiliser plusieurs métaux précieux dans le m˘me ouvrage, sauf dans les cas suivants: (
  58. a)stosowania cz´Êci ze z∏ota o próbie nie ni˝szej ni˝ 750 w wyrobach, które sk∏adajà si´ z cz´Êci platynowych, stanowiàcych wagowo wi´cej ni˝ 50 procent wszystkich cz´Êci metalowych pod warunkiem, ˝e z∏oto i platyna b´dà odró˝nia∏y si´ od siebie kolorem oraz ˝e w cz´Êci wykonanej z platyny taki wyrób b´dzie oznaczony jako platynowy znakami okreÊlonymi w ust´pie 5 za∏àcznika II, a z∏ote cz´Êci b´dà oznaczone tylko Wspólnà Cechà Kontroli. Jednak postanowienie to nie jest zobowiàzujàce dla Umawiajàcych si´ Paƒstw, w których ustawodawstwo nie zezwala na dopuszczenie do importu i sprzeda˝y wyrobów oznaczonych w ten sposób; (
  59. a)the use of gold parts of a fineness of not less than 750 on articles which contain platinum parts exceeding 50 per cent by weight of the total metallic parts, provided that the gold and platinum parts are distinguishable by colour and that the article is marked as platinum on the platinum part with the marks specified in paragraph 5 of Annex II, the gold part being marked only with the Common Control Mark. Notwithstanding this there shall be no obligation on Contracting States whose legislation would not allow hallmarking of this nature to accept such articles for importation or sale;
  60. a)les parties en or au titre minimum de 750 sont admises pour les ouvrages dans lesquels le poids des parties en platine représente plus de 50 pour cent du poids de toutes les parties métalliques, ∫ condition que les parties en or et en platine se distinguent par leur couleur et que de tels ouvrages soient marqués au titre du platine sur la partie platine avec les poin˜ons spécifiés au paragraphe 5 de l’Annexe II, la partie or étant marquée uniquement avec le Poin˜on Commun. Nonobstant il n’y a pas d’obligation pour un Etat Contractant dont la législation n’admet pas le poin˜onnement d’ouvrages de cette nature d’en accepter l’importation ou la vente; (
  61. b)stosowania cz´Êci platynowych w wyrobach, które zawierajà cz´Êci ze z∏ota, stanowiàce wagowo wi´cej ni˝ 50 procent wszystkich cz´Êci metalowych pod warunkiem, ˝e w cz´Êci wykonanej ze z∏ota wyrób oznaczony b´dzie jako z∏oty znakami, okreÊlonymi w ust´pie 5 za∏àcznika II; (
  62. b)the use of platinum parts on articles which contain gold parts exceeding 50 per cent by weight of the total metallic parts, provided that the article is marked as gold on the gold part with the marks specified in paragraph 5 of Annex II;
  63. b)les parties en platine sont admises pour les ouvrages dans lesquels le poids des parties en or représente plus de 50 pour cent du poids de toutes les parties métalliques, ∫ condition que de tels ouvrages soient marqués au titre de l’or sur la partie or avec les poin˜ons spécifiés au paragraphe 5 de l’Annexe II; (
  64. c)stosowania cz´Êci ze z∏ota i/lub platyny w wyrobach, które zawierajà cz´Êci srebrne, stanowiàce wagowo wi´cej ni˝ 50 procent wszystkich cz´Êci metalowych pod warunkiem, ˝e w cz´Êci wykonanej ze srebra wyrób taki b´dzie oznaczony jako srebrny znakami okreÊlonymi w ust´pie 5 za∏àcznika II; (
  65. c)the use of gold and/or platinum parts on articles which contain silver parts exceeding 50 per cent by weight of the total metallic parts, provided that the article is marked as silver on the silver part with the marks specified in paragraph 5 of Annex II;
  66. c)les parties en or et/ou en platine sont admises pour les ouvrages dans lesquels le poids des parties en argent représente plus de 50 pour cent du poids de toutes les parties métalliques, ∫ condition que de tels ouvrages soient marqués du titre de l’argent, sur la partie argent avec les poin˜ons spécifiés au paragraphe 5 de l’Annexe II; Dziennik Ustaw Nr 46 — 2999 — Poz. 297 (
  67. d)stosowania mniej szlachetnego metalu do wykonania drobnych ruchomych cz´Êci, takich jak j´zyczki klamer, które z przyczyn technicznych nie mogà byç wykonane z bardziej szlachetnego metalu pod warunkiem, ˝e na cz´Êci wykonanej z mniej szlachetnego metalu b´dzie odciÊni´te lub wygrawerowane konkretne okreÊlenie metalu. (
  68. d)the use of small working parts of a less precious metal, such as tongues for clasps, which for technical reasons cannot be made of the more precious metal, provided that the less precious part is stamped or engraved with a specific designation of the metal.
  69. d)si pour des raisons techniques les petites parties mobiles telles que les cliquets de fermoir ne peuvent ˘tre confectionnées avec le m˘me métal que l’ouvrage, elles seront admises en un métal précieux moins noble ∫ condition que ce dernier porte une désignation spécifique, insculpée ou gravée. 12. Poz∏acanie wyrobów wykonanych ze srebra jest dozwolone pod warunkiem, ˝e ca∏y wyrób oznaczony b´dzie jako srebrny. Pokrywanie wyrobów z bia∏ego z∏ota, srebra i platyny rodem jest dozwolone pod warunkiem, ˝e ca∏y wyrób oznaczony b´dzie odpowiednio jako z∏oty, srebrny lub platynowy. 12. The coating of silver articles with gold is permitted provided that the whole article is marked as silver. The coating of white gold, silver or platinum articles with rhodium is permitted provided that the whole article is marked as gold, silver or platinum respectively. 12. Il est permis, d’appliquer une couche d’or sur les ouvrages d’argent, ∫ condition que l’ouvrage soit marqué au titre de l’argent. Il est permis d’appliquer une couche de rhodium sur les ouvrages en or blanc, argent ou platine, ∫ condition que l’ouvrage soit marqué respectivement au titre de l’or, de l’argent ou du platine. 13. Stosowanie metalowych podk∏adów i pokryç wykoƒczeniowych w wyrobach z metali szlachetnych innych ni˝ okreÊlone w ust´pie 12, jest zabronione. 13. Undercoats or final coatings of metals, other than those permitted under paragraph 12, on precious metal articles shall be prohibited. 13. Il est interdit d’appliquer sur les ouvrages en métaux précieux des couches intermédiaires ou des couches de surface en autres métaux que ceux autorisés au paragraphe 12. 14. Cz´Êci wykonane z platyny, o których mowa w ust´pie 11(b), cz´Êci wykonane ze z∏ota lub platyny, o których mowa w ust´pie 11(c), cz´Êci wykonane z mniej szlachetnego metalu, o których mowa w ust´pie 11(d), oraz z∏oto do poz∏acania, o którym mowa w ust´pie 12, b´dà próby nie ni˝szej ni˝ minimalna próba, okreÊlona dla tych metali w ust´pie 2. 14. The parts of platinum referred to in paragraph 11(b), the parts of gold or platinum referred to in paragraph 11(c), the parts of less precious metal referred to in paragraph 11(d), and the gold coating referred to in paragraph 12 shall be of a fineness not less than the minimum standard of fineness for these metals as laid down in paragraph 2. 14. Les parties en platine auxquelles se réf¯re le paragraphe 11 b), celles en or ou en platine auxquelles se réf¯re le paragraphe 11 c), les parties en métal précieux moins noble auxquelles se réf¯re le paragraphe 11
  70. d)et l’application d’une couche d’or au sens du paragraphe 12 ne seront pas ∫ un titre inférieur aux titres minimaux fixés au paragraphe 2. Za∏àcznik II Annex II Annexe II KONTROLE PRZEPROWADZANE PRZEZ UPOWA˚NIONE URZ¢DY PROBIERCZE CONTROL BY THE AUTHORIZED ASSAY OFFICES CONTRÔLE EFFECTUÉ PAR LES BUREAUX DE CONTRÔLE DES MÉTAUX PRÉCIEUX RECONNUS 1. Upowa˝niony urzàd probierczy b´dzie bada∏, czy wyroby z metali szlachetnych zg∏aszane do niego w celu ocechowania Wspólnà Cechà Kontroli spe∏niajà warunki okreÊlone w za∏àczniku I do niniejszej konwencji. 1. An authorized assay office shall examine whether articles of precious metals which are presented to it in order to be marked with the Common Control Mark will fulfil the conditions of Annex I to this Convention. 1. Les bureaux de contrôle des métaux précieux reconnus examinent si les ouvrages en métaux précieux qui leur sont présentés pour l’apposition du Poin˜on Commun répondent aux conditions de l’Annexe I ∫ la présente Convention. Metody analizy Methods of analysis Méthodes d’analyse 2. Do badania wyrobów z metali szlachetnych upowa˝niony urzàd probierczy b´dzie stosowa∏ jednà z podanych ni˝ej metod analizy: 2. The authorized assay office shall use one of the following methods of analysis in assaying articles of precious metals: 2. Pour l’essai des ouvrages en métaux précieux le bureau de contrôle reconnu utilisera l’une des méthodes d’analyse suivantes: Dziennik Ustaw Nr 46 — 3000 — Poz. 297 dla z∏ota: analiz´ kupelacyjnà Gold: Cupellation Or: la coupellation dla srebra: analiz´ Gay-Lussaca lub Volharda, lub analiz´ potencjometrycznà Silver: Gay-Lussac or Volhard or Potentiometric Argent: Gay-Lussac ou Volhard ou potentiométrie dla platyny: metod´ grawimetrycznà (szeÊciochloroplatynianem amonowym) lub metod´ absorpcji atomowej, lub analiz´ spektrograficznà, lub analiz´ spektrofotometrycznà. Platinum: Gravimetric (Ammonium Chloroplatinate) or Atomic Absorption or Spectrographic or Spectrophotometric. Platine: gravimétrie (chloroplatinate d’ammonium) ou absorption atomique ou spectrographie ou spectrophotométrie. 3. Liczba pobieranych i analizowanych próbek musi byç taka, by dawa∏a urz´dowi probierczemu pewnoÊç, ˝e wszystkie cz´Êci wszystkich sprawdzanych wyrobów odpowiadajà wymaganej próbie. 3. The number of samples taken and analysed shall be sufficient to enable the assay office to be satisfied that all parts of all articles controlled are up to the required standards of fineness. 3. Le nombre de prises d’essai prélevées et analysées doit ˘tre suffisant pour permettre au bureau de contrôle de s’assurer que toutes les parties de tous les ouvrages vérifiés satisfont aux titres requis. 4. Niedopuszczalna jest tolerancja ujemna. Jednak upowa˝niony urzàd probierczy mo˝e zaakceptowaç wyniki badaƒ wykazujàce niewielkie odchylenia poni˝ej normy, mieszczàce si´ w granicach uznawanych niedok∏adnoÊci, wynikajàcych z zatwierdzonych metod badania. 4. No minus tolerance shall be permitted. The authorized assay office may, however, accept assay results showing a small deviation below standard falling within the margins of recognized inaccuracies in the approved assay methods. 4. Aucune tolérance en dessous du titre indiqué n’est admise. Le bureau de contrôle reconnu peut toutefois accepter des résultats d’essai faisant apparaître un léger écart entrant dans les limites de précision admises pour les méthodes d’essai reconnues. Cechowanie Marking Poin˜onnement 5. Stosuje si´ nast´pujàce znaki: 5. The following marks shall be applied: 5. On apposera les marques suivantes: (
  71. a)zarejestrowany znak wytwórcy zgodnie z opisem w ust´pie 7; (
  72. a)a registered responsibility mark as described in paragraph 7;
  73. a)un poin˜on de responsabilité enregistré, conforme ∫ la description donnée au paragraphe 7; (
  74. b)oznaczenie cyframi arabskimi, okreÊlajàce prób´ wyrobu w cz´Êciach na tysiàc; (
  75. b)a number in Arabic numerals showing the standard of fineness of the article in parts per thousand;
  76. b)un nombre en chiffres arabes indiquant le titre de l’ouvrage en milli¯mes; (
  77. c)znak upowa˝nionego urz´du probierczego; (
  78. c)the mark of the authorized assay office;
  79. c)le poin˜on du bureau de contrôle des métaux précieux reconnu; (
  80. d)Wspólna Cecha Kontroli zgodnie z opisem w ust´pie 8. (
  81. d)the Common Control Mark as described in paragraph 8.
  82. d)le Poin˜on Commun tel qu’il est décrit au paragraphe 8. Znaki (
  83. a)i (
  84. b)sà wybijane lub odlewane na wyrobie. Marks (
  85. a)and (
  86. b)shall be punched or cast on the article. Les marques
  87. a)et
  88. b)seront insculpées ou moulées sur l’ouvrage. Znaki (
  89. c)i (
  90. d)sà wybijane na wyrobie. Marks (
  91. c)and (
  92. d)shall be punched on the article. Les marques
  93. c)et
  94. d)seront insculpées. 6. Je˝eli wyrób sk∏ada si´ z jednej lub kilku cz´Êci, które sà umocowane zawiasowo lub ∏atwo oddzielajà si´ od podstawowej cz´Êci wyrobu, znaki wymienione wy˝ej b´dà mia∏y zastosowanie tylko do cz´Êci podstawowej. W takich 6. If an article consists of parts, one or more of which are hinged or readily separable from the main part of the article, the above marks shall be applied only to the main part. In such case the assay office shall where practicable apply the 6. Lorsqu’un ouvrage est constitué de plusieurs parties dont l’une ou plusieurs d’entre elles sont articulées ou facilement détachables du corps de l’ouvrage, les marques indiquées ci-dessus ne seront apposées que sur la partie Dziennik Ustaw Nr 46 — 3001 — Poz. 297 przypadkach tam, gdzie jest to mo˝liwe, na pozosta∏ych cz´Êciach urzàd probierczy zastosuje Wspólnà Cech´ Kontroli. Common Control Mark to the other parts. principale. Dans ce cas, le bureau de contrôle apposera, dans la mesure du possible, le Poin˜on Commun sur les autres parties. 7. Znak wytwórcy, o którym mowa w ust´pie 5(a), b´dzie sk∏ada∏ si´ z nazwy wytwórcy, jej skrótu lub symbolu, który zosta∏ wprowadzony do urz´dowego rejestru Umawiajàcego si´ Paƒstwa lub jednego z jego upowa˝nionych urz´dów probierczych, na którego terytorium dany wyrób jest kontrolowany. 7. The responsibility mark referred to in paragraph 5(
  95. a)shall consist of the name of the sponsor, an abbreviation thereof or a symbol, which has been entered into an official register of the Contracting State, or one of its authorized assay offices, in whose territory the article in question is controlled. 7. Le poin˜on de responsabilité auquel se réf¯re le paragraphe 5
  96. a)reproduira le nom du responsable ou une abréviation de celui-ci, ou un symbole, et sera inscrit au registre officiel de l’Etat Contractant ou ∫ l’un de ses bureaux de contrôle reconnus sur le territoire duquel l’ouvrage en question est contrôlé. 8. Wspólna Cecha Kontroli b´dzie si´ sk∏ada∏a z rysunkowego przedstawienia wagi ze ˝∏obionymi cyframi arabskimi, okreÊlajàcymi prób´ wyrobu w cz´Êciach na tysiàc, umieszczonymi na liniowanym tle w obwódce wskazujàcej na rodzaj metalu szlachetnego zgodnie z poni˝szymi rysunkami: 8. The Common Control Mark shall consist of the representation of a balance together with the number in Arabic numerals showing the standard of fineness of the article in parts per thousand in relief on a lined background surrounded by a shield indicating the nature of the precious metal as follows: 8. Le Poin˜on Commun comportera en relief sur fond linéaire l’image d’une balance et l’indication du titre de l’ouvrage en chiffres arabes et en milli¯mes, le tout dans un encadrement indiquant la nature du métal précieux de la mani¯re suivante: — dla wyrobów ze z∏ota: — for gold articles: — pour les ouvrages d’or: — dla wyrobów ze srebra: — for silver articles: — pour les ouvrages d’argent: — dla wyrobów z platyny: — for platinum articles: — pour les ouvrages de platine: Przyk∏ady wzorów Wspólnej Cechy Kontroli przedstawione sà w za∏àczniku. Examples of the design of the Common Control Mark are reproduced at Appendix. Des mod¯les du Poin˜on Commun sont reproduits dans l’Appendice. 9. Je˝eli upowa˝niony urzàd probierczy uzna wyrób za zgodny z postanowieniami za∏àcznika I do niniejszej konwencji, mo˝e on oznaczyç taki wyrób swoim znakiem wyznaczonego urz´du probierczego i Wspólnà Cechà Kontroli. W przypadkach zastosowania Wspólnej Cechy Kontroli, upowa˝niony urzàd probierczy zadba, by przed opuszczeniem jego siedziby wyrób zosta∏ nale˝ycie ocechowany zgodnie z postanowieniami ust´pu 5 i 6. Tam, gdzie jest to mo˝liwe, wszystkie znaki b´dà umieszczone blisko siebie. 9. If the article is found by the authorized assay office to comply with the provisions of Annex I to this Convention the authorized assay office may mark the article with its appointed assay office mark and the Common Control Mark. In cases where the Common Control Mark is applied the authorized assay office shall, before the article leaves its custody, ensure that the article is fully marked in accordance with the provisions of paragraphs 5 and 6. Whenever possible all marks shall be placed in immediate proximity to each other. 9. Si le bureau de contrôle reconnu constate que l’ouvrage répond aux dispositions de l’Annexe I de la présente Convention, il peut le marquer de son poin˜on de contrôle et du Poin˜on Commun. S’il appose le Poin˜on Commun, le bureau de contrôle reconnu s’assurera, avant de restituer l’ouvrage, que celui-ci comporte toutes les marques conformément aux dispositions des paragraphes 5 et 6. Dans la mesure du possible tous les poin˜ons seront apposés ∫ proximité immédiate les uns des autres. Dziennik Ustaw Nr 46 — 3002 — Za∏àcznik Poz. 297 Appendix Appendice PRZYK¸ADY WSPÓLNEJ CECHY KONTROLI EXAMPLES OF THE COMMON CONTROL MARK MODÈLES DU POINÇON COMMUN Dla wyrobów ze z∏ota próby 750 For gold articles of the standard of fineness 750 Pour les ouvrages d’or au titre de 750 Dla wyrobów ze srebra próby 925 For silver articles of the standard of fineness 925 Pour les ouvrages d’argent au titre de 925 Dla wyrobów z platyny próby 950 For platinum articles of the standard of fineness 950 Pour les ouvrages de platine au titre de 950 Po zaznajomieniu si´ z powy˝szà konwencjà, w imieniu Rzeczypospolitej Polskiej oÊwiadczam, ˝e: — zosta∏a ona uznana za s∏usznà zarówno w ca∏oÊci, jak i ka˝de z postanowieƒ w niej zawartych, — Rzeczpospolita Polska postanawia przystàpiç do tej konwencji, — postanowienia konwencji sà przyj´te, potwierdzone i b´dà niezmiennie zachowywane. Na dowód czego wydany zosta∏ akt niniejszy, opatrzony piecz´cià Rzeczypospolitej Polskiej. Dano w Warszawie dnia 19 lipca 2005 r. Prezydent Rzeczypospolitej Polskiej: A. KwaÊniewski L.S. Prezes Rady Ministrów: M. Belka

🔗 Do źródła urzędowego

Wyjaśnienie AI na podstawie urzędowego tekstu ustawy. Orientacyjne, nie zastępuje porady prawnej.