📄 Likuma teksts
Par Nolīguma pielikumu grozījumu spēkā stāšanos
Uzmanību! Jūs lietojat neatbilstošu interneta pārlūkprogrammu.
Lai varētu lietot visas Likumi.lv piedāvātās iespējas, piedāvājam BEZ MAKSAS ielādēt jaunāku pārlūkprogrammas versiju. Iesakām izmēģināt arī vietnes MOBILO VERSIJU - m.likumi.lv (piemērota arī mazāk jaudīgiem datoriem).
nerādīt turpmāk šo paziņojumu
Apstiprināt
Paldies par viedokli!
Rādīt vēlāk
LATVIJAS REPUBLIKAS TIESĪBU AKTI
veidi
tēmas
visvairāk skatītie
jaunākie
LV
EN
uz sākumu
meklēt
Izvērstā meklēšana
Noklusējuma vērtības
Izvērstā meklēšana
Kā meklēt?
Meklēt nosaukumā
meklēt locījumos
meklēt frāzi
Meklēt tekstā
meklēt locījumos
meklēt frāzi
Izdevējs
Veids
nemeklēt grozījumos
Pieņemts
Stājas spēkā
Dokumenta Nr.
līdz
līdz
Publicēts LV
Zaudējis spēku
Redakcija uz
līdz
līdz
Statuss:
spēkā esošs
vēl nav spēkā
zaudējis spēku
meklēt
notīrīt
Ārlietu
ministrijas dienesta informācija Nr.41/896-6715
Rīgā 2007.gada 27.jūlijā
Par Nolīguma
pielikumu grozījumu spēkā stāšanos
Ārlietu ministrija nosūta
publicēšanai 1957.gada 30.septembra Eiropas valstu nolīguma
par bīstamo kravu starptautiskajiem pārvadājumiem ar
autotransportu (ADR) A un B pielikuma grozījumus.
Grozījumi stājās spēkā 2007.gada
1.janvārī.
Nolīguma teksta tulkojums latviešu
valodā publicēts laikrakstā "Latvijas Vēstnesis" 1995.gada
10.oktobrī, Nr.155 (438).
Ārlietu ministrijas Juridiskā
departamenta
direktora p.i. I.Bīlmane
Acts whose
publication is obligatory
Publication in accordance with
Article 1 of Commission Directive 2006/xx/EC1
adapting for the sixth time to technical progress Council
Directive 94/55/EC2
on the approximation of the laws of the Member States
with regard to the transport of dangerous goods by
road3
1 January 2007 edition of ADR
(Amendments to 1 January 2005
edition only)
EUROPEAN
AGREEMENT CONCERNING THE INTERNATIONAL CARRIAGE
OF DANGEROUS GOODS BY ROAD (ADR)
Amendments to
annexes A and B of ADR
for entry into force on 1 January 2007
Wherever they appear in ADR
replace the words "porous mass" with "porous material" (apply
to 4.1.4.1 P200 (10)(p) (twice) and P200 (11), 4.1.6.2, 6.2.1.1.2
(twice), 6.2.1.5.1 (j), 6.2.1.6.2, 6.2.1.7.2 (f), (j) and (k),
6.2.5.2.3 and 6.2.5.8.2 (g), (k) and (l)).
PART 1
Chapter 1.1
1.1.3.1 (d) Amend to read as
follows:
"(d) the carriage undertaken by or
under the supervision of the emergency services, insofar as such
carriage is necessary in relation to the emergency response, in
particular carriage undertaken:
- by breakdown vehicles carrying
vehicles which have been involved in accidents or have broken
down and contain dangerous goods; or
- to contain and recover the
dangerous goods involved in an incident or accident and move them
to a safe place;".
1.1.3.1 Add a new sub paragraph
(f) to read:
"(f) the carriage of uncleaned
empty static or storage vessels and tanks which have contained
gases of Class 2, groups A, O or F, substances of Class 3 or
Class 9 belonging to packing group II or III or pesticides of
Class 6.1 belonging to packing group II or III, subject to the
following conditions:
- All openings with the exception
of pressure relief devices (when fitted) are hermetically
closed;
- Measures have been taken to
prevent any leakage of contents in normal conditions of carriage;
and
- The load is fixed in cradles or
crates or other handling devices or to the vehicle or container
in such a way that they will not become loose or shift during
normal conditions of carriage.
This exemption does not apply to
static or storage vessels and tanks which have contained
desensitized explosives or substances the carriage of which is
prohibited by ADR.".
1.1.3.2 (d) Amend to read as
follows:
"(d) gases contained in the
equipment used for the operation of the vehicle
(e.g. fire extinguishers), including in spare parts
(e.g. inflated pneumatic tyres); this exemption also applies to
inflated pneumatic tyres carried as a load;".
1.1.3.2 (f) Delete. Current (g)
becomes (f).
1.1.4.2.1 In the last sentence
replace "classes 1 to 8" with "classes 1 to 9".
1.1.4.2.2 Insert a new paragraph
to read as follows:
"1.1.4.2.2 Transport units
composed of a vehicle or vehicles other than those carrying
containers, portable tanks or tank containers as provided for in
1.1.4.2.1 (c), which are not placarded in accordance with the
provisions of 5.3.1 of ADR but which are marked and placarded in
accordance with Chapter 5.3 of the IMDG Code, shall be accepted
for carriage in a transport chain including maritime transport
provided that the orange-coloured plate marking provisions of
5.3.2 of ADR are complied with.".
Consequential
amendments: Renumber existing paragraph 1.1.4.2.2 as 1.1.4.2.3.
Delete the note under paragraph 5.3.1.5.2.
1.1.4.3 In the title insert "IMO
type" before "portable tanks".
In the first sentence, replace
"Portable tanks" with "IMO type portable tanks (types 1, 2, 5 and
7)" and replace "(Amdt. 30.00)" with "(Amdt. 33.06)".
Add a reference "1" to a footnote at the end. The
footnote will read as follows:
"1 The International Maritime
Organization (IMO) has issued "Guidance on the Continued Use of
Existing IMO Type Portable Tanks and Road Tank Vehicles for the
Transport of Dangerous Goods" as circular DSC.1/Circ.12 and
Corrigenda. The text of this guidance can be found on the IMO
website at: www.imo.org.".
Chapter 1.2
1.2.1 Insert the following new
definitions in alphabetical order:
""ASTM" means the American
Society for Testing and Materials (ASTM International, 100 Barr
Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959,
United States of America);"
Consequential
amendment: In Chapter 3.3, SP 649, delete the address in footnote
(2).
""Capacity of shell or shell
compartment" for tanks, means the total inner volume of the
shell or shell compartment expressed in litres or cubic metres.
When it is impossible to completely fill the shell or the shell
compartment because of its shape or construction, this reduced
capacity shall be used for the determination of the degree of
filling and for the marking of the tank;"
""CGA" means the Compressed
Gas Association (CGA, 4221 Walney Road, 5th Floor, Chantilly VA
20151-2923, United States of America);"
""ICAO" means the
International Civil Aviation Organization (ICAO, 999 University
Street, Montreal, Quebec H3C 5H7, Canada);"
""IMO" means the
International Maritime Organization (IMO, 4 Albert Embankment,
London SE1 7SR, United Kingdom);"
""Member of a vehicle crew"
means a driver or any other person accompanying the driver for
safety, security, training or operational reasons;"
""Tank record means" a file
containing all the important technical information concerning a
tank, a battery-vehicle or a MEGC, such as certificates referred
to in 6.8.2.3, 6.8.2.4 and 6.8.3.4;"
""UIC" means the
International Union of Railways (UIC, 16 rue Jean Rey, F-75015
Paris, France);"
Consequential
amendment: In 7.1.3, delete footnote 1).
""UNECE" means the United
Nations Economic Commission for Europe (UNECE, Palais des
Nations, 8-14 avenue de la Paix, CH-1211 Geneva 10,
Switzerland);"
Consequential
amendment: Wherever they appear in ADR replace the words "UN/ECE"
and "UN-ECE" with "UNECE". (Apply to 5.4.1.4.2 footnote 2) and to
section 5.4.2 footnote 3)).
In the definition of "Aerosol
or aerosol dispenser", insert "under pressure" after
"liquefied or dissolved".
In the definition of
"Hermetically closed tank", the second and fourth indents,
replace "as allowed by special provision TE15 of 6.8.4" with "in
accordance with the requirements of 6.8.2.2.3" at the end.
In the definition of "Manual of
Tests and Criteria", replace "(ST/SG/AC.10/11/Rev.4)" with
"(ST/SG/AC.10/11/Rev.4 as amended by document
ST/SG/AC.10/11/Rev.4/Amend.1)".
In the definition of
"Overpack", replace "by a single consignor" with "(by a
single consignor in the case of Class 7 )".
In sub-paragraph (a), replace
"plastic" with "plastics".
In the definition of "UN Model
Regulations", replace "thirteenth" with "fourteenth" and
"(ST/SG/AC.10/1/Rev.13)" with "(ST/SG/AC.10/1/Rev.14)".
Chapter 1.3
1.3.2.4 Replace "the radiation
hazards involved and" with "radiation protection including".
Replace "to ensure restriction of
their exposure and that" with "to restrict their occupational
exposure and the exposure".
Chapter 1.4
1.4.2.2.5 Add a new paragraph to
read as follows:
"1.4.2.2.5 (Reserved)".
1.4.3.3 Add a new subparagraph (j)
to read as follows:
"(j) he shall, when filling
vehicles or containers with dangerous goods in bulk, ascertain
that the relevant provisions of Chapter 7.3 are complied
with.".
Consequential
amendment: In 1.4.3.3, add a new subparagraph (i) to read as
follows:
"(i) (Reserved)".
Chapter 1.5
1.5.1.1 In the first sentence,
replace "For the purpose of adapting the requirements of ADR to
technological and industrial developments" with "In accordance
with Article 4, paragraph 3 of ADR".
Chapter 1.6
1.6.1.1 Replace "2005" with "2007"
and "2004" with "2006".
1.6.1.2 Amend to read as
follows:
"1.6.1.2 (a) The danger labels and
placards which until 31 December 2004 conformed to models No. 7A,
7B, 7C, 7D or 7E prescribed up to that date may be used until 31
December 2010.
(b) The danger labels and placards
which until 31 December 2006 conformed to model No. 5.2
prescribed up to that date may be used until 31 December
2010.".
1.6.1.11 Add a new transitional
measure to read as follows:
"1.6.1.11 Type approvals for
drums, jerricans and composite packagings made of high or medium
molecular mass polyethylene, and for high molecular mass
polyethylene IBCs, issued before 1 July 2007 in accordance with
the requirements of 6.1.6.1 (a) in force up to 31 December 2006,
but which are not in accordance with the requirements of 6.1.6.1
(a) applicable as from 1 January 2007, continue to be
valid.".
1.6.2.4 Add a new transitional
measure to read as follows:
"1.6.2.4 Pressure receptacles
designed and constructed in accordance with technical codes no
longer recognized according to 6.2.3 may still be used.".
1.6.2.5 Add a new transitional
measure to read as follows:
"1.6.2.5 Pressure receptacles and
their closures designed and constructed in accordance with
standards applicable at the time of their construction and no
longer listed in 6.2.2 or 6.2.5 may still be used.".
1.6.3.15 Add a new transitional
measure to read as follows:
"1.6.3.15 Fixed tanks
(tank-vehicles) and demountable tanks constructed before 1 July
2007 in accordance with the requirements in force up to 31
December 2006 but which do not, however, conform to the
requirements of 6.8.2.2.3 applicable as from 1 January 2007 may
continue to be used until the next periodic inspection.".
1.6.3.16 Add a new transitional
measure to read as follows:
"1.6.3.16 For fixed tanks
(tank-vehicles), demountable tanks and battery-vehicles
constructed before 1 January 2007 which do not conform to the
requirements of 4.3.2, 6.8.2.4 and 6.8.3.4 concerning the tank
record, the retention of files for the tank record shall start at
the latest at the next periodic inspection.".
1.6.3.17 Add a new transitional
measure to read as follows:
"1.6.3.17 Fixed tanks
(tank-vehicles) and demountable tanks intended for the carriage
of substances of Class 3, packing group I having a vapour
pressure of not more than 175 kPa (1.75 bar) (absolute)
at 50 °C, constructed before 1 July 2007 in accordance
with the requirements applicable up to 31 December 2006, to which
tank code L1.5BN had been assigned in accordance with the
requirements applicable up to 31 December 2006, may continue
to be used for the carriage of the substances mentioned above,
until 31 December 2018.".
1.6.3.25 The first amendment does
not apply to the English text.
Add the following new paragraph at
the end:
"The type of the test ("P" or "L")
required by 6.8.2.5.1 need not be added to the tank plate until
the first test after 1 January 2007 is performed.".
1.6.3.26 Amend to read as
follows:
"1.6.3.26 Fixed tanks
(tank-vehicles) and demountable tanks constructed before 1
January 2007 in accordance with the requirements in force up to
31 December 2006 but which do not, however, conform to the
requirements applicable as from 1 January 2007 regarding the
marking of the external design pressure in accordance with
6.8.2.5.1, may still be used.".
1.6.3.31 Amend to read as
follows:
"1.6.3.31 Fixed tanks
(tank-vehicles), demountable tanks and battery-vehicles designed
and constructed in accordance with technical codes no longer
recognized according to 6.8.2.7 may still be used.".
1.6.4.6 Amend to read as
follows:
"1.6.4.6 Tank-containers
constructed before 1 January 2007 in accordance with the
requirements in force up to 31 December 2006 but which do not,
however, conform to the requirements applicable as from 1 January
2007 regarding the marking of the external design pressure in
accordance with 6.8.2.5.1, may still be used.".
1.6.4.9 Amend to read as
follows:
"1.6.4.9 Tank-containers and MEGCs
designed and constructed in accordance with technical codes no
longer recognized according to 6.8.2.7 may still be used.".
1.6.4.12 Add a new sentence, at
the end, to read as follows:
"Until the relevant code marking
has been carried out, the proper shipping name of the substance
carried1 shall be indicated
on the tank-container itself or on a plate.".
Consequential
amendment: Renumber existing footnotes accordingly.
1.6.4.15 The first amendment does
not apply to the English text.
Add the following new paragraph at
the end:
"The type of the test ("P" or "L")
required by 6.8.2.5.1 need not be added to the tank plate until
the first test after 1 January 2007 is performed.".
1.6.4.17 Add a new transitional
measure to read as follows:
"1.6.4.17 Tank-containers
constructed before 1 July 2007 in accordance with the
requirements in force up to 31 December 2006 but which do not
conform to the requirements of 6.8.2.2.3 applicable as from 1
January 2007 may continue to be used until the next periodic
inspection.".
1.6.4.18 Add a new transitional
measure to read as follows:
"1.6.4.18 For tank-containers
constructed before 1 January 2007 which do not conform to the
requirements of 4.3.2, 6.8.2.4 and 6.8.3.4 concerning the tank
record, the retention of files for the tank record shall start at
the latest at the next periodic inspection.".
1.6.4.19 Add a new transitional
measure to read as follows:
"1.6.4.19 Tank-containers intended
for the carriage of substances of Class 3, packing group I having
a vapour pressure of not more than 175 kPa (1.75 bar)
(absolute) at 50 °C, constructed before 1 July 2007 in
accordance with the requirements applicable up to 31 December
2006, to which tank code L1.5BN had been assigned in accordance
with the requirements applicable up to 31 December 2006, may
continue to be used for the carriage of the substances mentioned
above until 31 December 2016.".
1.6.4.30 Add a new transitional
measure to read as follows:
"1.6.4.30 The competent authority
may continue to issue, until 31 December 2007, design approval
certificates for new designs of portable tanks and UN MEGCs which
meet the requirements of Chapter 6.7 in force up to 31 December
2006. Portable tanks and UN MEGCs which do not meet the design
requirements applicable as from 1 January 2007 but which have
been constructed according to a design approval certificate which
has been issued before 1 January 2008 may continue to be
used.".
Consequential
amendment: Amend the title of section 1.6.4 to read as follows:
"1.6.4 Tank-containers, portable tanks and MEGCs".
1.6.5.8 Replace "may continue to
be used until 31 December 2014" with "may still be used".
1.6.5.10 Add a new transitional
measure to read as follows:
"1.6.5.10 Certificates of
approval, which conform to the model shown in 9.1.3.5 applicable
up to 31 December 2006, may continue to be used.".
1.6.6.2.2 In the first sentence,
delete "until 31 December 2003" and insert "the multilateral
approval of package design;" before "the mandatory programme of
quality assurance".
Delete the sentence: "After this
date use may continue subject, additionally, to multilateral
approval of package design.".
Chapter 1.7
1.7.2.3 Insert the following new
first sentence "Doses to persons shall be below the relevant dose
limits.".
At the end of current first
sentence (new second sentence), replace "and doses to persons
shall be below the relevant dose limits." with "within the
restriction that the doses to individuals be subject to dose
constraints.".
1.7.2.4 In the French version,
replace "dose effective" with "dose efficace".
Delete indent (a) and renumber (b)
and (c) as (a) and (b).
1.7.4.1 Insert "of radioactive
material" after "which consignments" and "applicable" after
"satisfy all the".
Delete "applicable to radioactive
material" at the end.
Chapter 1.8
1.8.3.10 Add a new second sentence
to read as follows: "The examining body shall not be a training
provider.".
1.8.3.12 Amend to read as
follows:
"1.8.3.12
Examinations
1.8.3.12.1 The examination shall
consist of a written test which may be supplemented by an oral
examination.
1.8.3.12.2 The use in the written
test of documentation other than international or national
regulations is not permitted.
1.8.3.12.3 Electronic media may be
used only if provided by the examining body. There shall be no
means of a candidate introducing further data to the electronic
media provided; the candidate may only answer the questions
posed.
1.8.3.12.4 Second sentence of
current 1.8.3.12 followed by sub-paragraphs (a) and (b) with the
following amendment: At the beginning of this second sentence,
replace "written examination" by "written test" .".
Consequential
amendment: In 1.8.3.16.2, replace "1.8.3.12 (b)" with "1.8.3.12.4
(b)" at the end.
1.8.5.1 Amend to read as
follows:
"1.8.5.1 If a serious accident or
incident takes place during loading, filling, carriage or
unloading of dangerous goods on the territory of a Contracting
Party, the loader, filler, carrier or consignee, respectively,
shall ascertain that a report conforming to the model prescribed
in 1.8.5.4 is made to the competent authority of the Contracting
Party concerned.".
Chapter 1.10
1.10.1.4 Amend to read as
follows:
"Each member of a vehicle crew
shall carry with them means of identification, which includes
their photograph, during carriage of dangerous goods.".
Table 1.10.5 For Class 6.2, insert
"(UN Nos. 2814 and 2900)" after "Category A".
For Class 6.2, in column "Bulk",
replace letter "a" by "0".
Delete the NOTE.
1.10.6 Add a new paragraph after
Table 1.10.5 to read as follows:
"1.10.6 For radioactive material,
the provisions of this Chapter are deemed to be complied with
when the provisions of the Convention on Physical Protection of
Nuclear Material and of IAEA INFCIRC/225 (Rev.4) are
applied.".
PART 2
Chapter 2.2
2.2.1.1.7 Current 2.2.1.1.7
becomes new 2.2.1.1.8. Insert the following new paragraphs:
"2.2.1.1.7 Assignment of
fireworks to divisions
2.2.1.1.7.1 Fireworks shall
normally be assigned to divisions 1.1, 1.2, 1.3, and 1.4 on the
basis of test data derived from Test Series 6 of the Manual of
Tests and Criteria. However, since the range of such articles is
very extensive and the availability of test facilities may be
limited, assignment to divisions may also be made in accordance
with the procedure in 2.2.1.1.7.2.
2.2.1.1.7.2 Assignment of
fireworks to UN Nos. 0333, 0334, 0335 and 0336 may be made on the
basis of analogy, without the need for Test Series 6 testing, in
accordance with the default fireworks classification table
in 2.2.1.1.7.5. Such assignment shall be made with the
agreement of the competent authority. Items not specified in the
table shall be classified on the basis of test data derived from
Test Series 6.
NOTE 1: The
addition of other types of fireworks to column 1 of the table in
2.2.1.1.7.5 shall only be made on the basis of full test data
submitted to the UN Sub-Committee of Experts on the Transport of
Dangerous Goods for consideration.
NOTE 2: Test data
derived by competent authorities which validates, or contradicts
the assignment of fireworks specified in column 4 of the table
in 2.2.1.1.7.5 to divisions in column 5 should be submitted
to the UN Sub-Committee of Experts on the Transport of Dangerous
Goods for information.
2.2.1.1.7.3 Where fireworks of
more than one division are packed in the same package, they shall
be classified on the basis of the most dangerous division unless
test data derived from Test Series 6 indicate otherwise.
2.2.1.1.7.4 The classification
shown in the table in 2.2.1.1.7.5 applies only for articles
packed in fibreboard boxes (4G).
2.2.1.1.7.5 Default fireworks
classification table 1
NOTE 1: References to
percentages in the table, unless otherwise stated, are to the
mass of all pyrotechnic composition (e.g. rocket motors, lifting
charge, bursting charge and effect charge).
NOTE 2: "Flash
composition" in this table refers to pyrotechnic compositions
containing an oxidizing substance, or black powder, and a metal
powder fuel that are used to produce an aural report
effect or used as a bursting charge in fireworks devices.
NOTE 3: Dimensions in mm
refer to:
- for
spherical and peanut shells the diameter of the sphere of the
shell;
- for cylinder
shells the length of the shell;
- for a shell
in mortar, Roman candle, shot tube firework or mine the inside
diameter of the tube comprising or containing the firework;
- for a bag
mine or cylinder mine, the inside diameter of the mortar intended
to contain the mine.
Type
Includes: /
Synonym:
Definition
Specification
Classification
Shell, spherical or
cylindrical
Spherical display shell: aerial
shell, colour shell, dye shell, multi-break shell,
multi-effect shell, nautical shell, parachute shell, smoke
shell, star shell; report shell: maroon, salute, sound
shell, thunderclap, aerial shell kit
Device with or without
propellant charge, with delay fuse and bursting charge,
pyrotechnic unit(s) or loose pyrotechnic composition and
designed to be projected from a mortar
All report shells
1.1G
Colour shell: ≥ 180 mm
1.1G
Colour shell: < 180 mm
with > 25% flash composition, as loose powder and/
or report effects
1.1G
Colour shell: < 180 mm
with ≤ 25% flash composition, as loose powder and/ or
report effects
1.3G
Colour shell: ≤ 50 mm, or
≤ 60 g pyrotechnic composition, with ≤ 2% flash
composition as loose powder and/ or report effects
1.4G
Peanut shell
Device with two or more
spherical aerial shells in a common wrapper propelled by
the same propellant charge with separate external delay
fuses
The most hazardous spherical
aerial shell determines the classification
Preloaded mortar, shell in
mortar
Assembly comprising a spherical
or cylindrical shell inside a mortar from which the shell
is designed to be projected
All report shells
1.1G
Colour shell: ≥ 180 mm
1.1G
Colour shell: > 50 mm
and < 180 mm
1.2G
Colour shell:
≤ 50 mm, or < 60 g pyrotechnic
composition, with ≤ 25% flash composition as loose
powder and/ or report effects
1.3G
Shell, spherical or
cylindrical
(cont'd)
Shell of shells (spherical)
(Reference to percentages for
shell of shells are to the gross mass of the fireworks
article)
Device without propellant
charge, with delay fuse and bursting charge, containing
report shells and inert materials and designed to be
projected from a mortar
> 120 mm
1.1G
Device without propellant
charge, with delay fuse and bursting charge, containing
report shells ≤ 25g flash composition per report unit, with
≤ 33% flash composition and ≥ 60% inert materials and
designed to be projected from a mortar
≤ 120 mm
1.3G
Device without propellant
charge, with delay fuse and bursting charge, containing
colour shells and/or pyrotechnic units and designed to be
projected from a mortar
> 300 mm
1.1G
Device without propellant
charge, with delay fuse and bursting charge, containing
colour shells ≤ 70mm and/or pyrotechnic units, with ≤
25% flash composition and ≤ 60% pyrotechnic
composition and designed to be projected from a mortar
> 200 mm and
≤ 300 mm
1.3G
Device with propellant charge,
with delay fuse and bursting charge, containing colour
shells ≤ 70 mm and/or pyrotechnic units, with ≤ 25%
flash composition and ≤ 60% pyrotechnic composition
and designed to be projected from a mortar
≤ 200 mm
1.3G
Battery/ combination
Barrage, bombardos, cakes,
finale box, flowerbed, hybrid, multiple tubes, shell cakes,
banger batteries, flash banger batteries
Assembly including several
elements either containing the same type or several types
each corresponding to one of the types of fireworks listed
in this table, with one or two points of ignition
The most hazardous firework
type determines the classification
Roman candle
Exhibition candle, candle,
bombettes
Tube containing a series of
pyrotechnic units consisting of alternate pyrotechnic
composition, propellant charge, and transmitting fuse
≥ 50 mm inner diameter,
containing flash composition, or <50 mm with >25%
flash composition
1.1G
≥ 50 mm inner diameter,
containing no flash composition
1.2G
< 50 mm inner
diameter and ≤ 25% flash composition
1.3G
≤ 30 mm inner
diameter, each pyrotechnic unit ≤ 25 g and
≤ 5% flash composition
1.4G
Shot tube
Single shot Roman candle, small
preloaded mortar
Tube containing a pyrotechnic
unit consisting of pyrotechnic composition, propellant
charge with or without transmitting fuse
≤ 30 mm inner
diameter and pyrotechnic unit > 25 g, or >
5% and ≤ 25% flash composition
1.3G
≤ 30 mm inner
diameter, pyrotechnic unit ≤ 25 g and ≤ 5%
flash composition
1.4G
Rocket
Avalanche rocket, signal
rocket, whistling rocket, bottle rocket, sky rocket,
missile type rocket, table rocket
Tube containing pyrotechnic
composition and/or pyrotechnic units, equipped with
stick(s) or other means for stabilization of flight, and
designed to be propelled into the air
Flash composition effects
only
1.1G
Flash composition > 25%
of the pyrotechnic composition
1.1G
> 20 g pyrotechnic
composition and flash composition ≤ 25%
1.3G
≤ 20 g pyrotechnic composition,
black powder bursting charge and ≤ 0.13 g flash
composition per report and ≤ 1 g in total
1.4G
Mine
Pot-a-feu, ground mine, bag
mine, cylinder mine
Tube containing propellant
charge and pyrotechnic units and designed to be placed on
the ground or to be fixed in the ground. The principal
effect is ejection of all the pyrotechnic units in a single
burst producing a widely dispersed visual and/or aural
effect in the air or:
Cloth or paper bag or cloth or
paper cylinder containing propellant charge and pyrotechnic
units, designed to be placed in a mortar and to function as
a mine
> 25% flash composition, as
loose powder and/ or report effects
1.1G
≥ 180 mm and ≤ 25% flash
composition, as loose powder and/ or report effects
1.1G
< 180 mm and ≤ 25%
flash composition, as loose powder and/ or report
effects
1.3G
≤ 150 g pyrotechnic
composition, containing ≤ 5% flash composition as loose
powder and/ or report effects. Each pyrotechnic unit ≤ 25
g, each report effect < 2g ; each whistle, if any,
≤ 3 g
1.4G
Fountain
Volcanos, gerbs, showers,
lances, Bengal fire, flitter sparkle, cylindrical
fountains, cone fountains, illuminating torch
Non-metallic case containing
pressed or consolidated pyrotechnic composition producing
sparks and flame
≥ 1 kg pyrotechnic
composition
1.3G
< 1 kg pyrotechnic
composition
1.4G
Sparkler
Handheld sparklers,
non-handheld sparklers, wire sparklers
Rigid wire partially coated
(along one end) with slow burning pyrotechnic composition
with or without an ignition tip
Perchlorate based sparklers:
> 5 g per item or > 10 items per pack
1.3G
Perchlorate based sparklers: ≤
5 g per item and ≤ 10 items per pack;
Nitrate based sparklers: ≤ 30 g
per item
1.4G
Bengal stick
Dipped stick
Non-metallic stick partially
coated (along one end) with slow-burning pyrotechnic
composition and designed to be held in the hand
Perchlorate based items: > 5
g per item or > 10 items per pack
1.3 G
Perchlorate based items: ≤ 5 g
per item and ≤ 10 items per pack; nitrate based items: ≤ 30
g per item
1.4G
Low hazard fireworks and
novelties
Table bombs, throwdowns,
crackling granules, smokes, fog, snakes, glow worm,
serpents, snaps, party poppers
Device designed to produce very
limited visible and/ or audible effect which contains small
amounts of pyrotechnic and/ or explosive composition.
Throwdowns and snaps may
contain up to 1.6 mg of silver fulminate; snaps and party
poppers may contain up to 16 mg of potassium chlorate/ red
phosphorous mixture; other articles may contain up to
5 g of pyrotechnic composition, but no flash
composition
1.4G
Spinner
Aerial spinner, helicopter,
chaser, ground spinner
Non-metallic tube or tubes
containing gas- or spark-producing pyrotechnic composition,
with or without noise producing composition, with or
without aerofoils attached
Pyrotechnic composition per
item > 20 g, containing ≤ 3% flash composition
as report effects, or whistle composition
≤ 5 g
1.3G
Pyrotechnic composition per
item ≤ 20 g, containing ≤ 3% flash composition as
report effects, or whistle composition ≤ 5 g
1.4G
Wheels
Catherine wheels, Saxon
Assembly including drivers
containing pyrotechnic composition and provided with a
means of attaching it to a support so that it can
rotate
≥ 1 kg total
pyrotechnic composition, no report effect, each whistle (if
any) ≤ 25 g and ≤ 50 g whistle composition per
wheel
1.3G
< 1 kg total
pyrotechnic composition, no report effect, each whistle (if
any) ≤ 5 g and ≤ 10 g whistle composition per
wheel
1.4G
Aerial wheel
Flying Saxon, UFO's, rising
crown
Tubes containing propellant
charges and sparks- flame- and/ or noise producing
pyrotechnic compositions, the tubes being fixed to a
supporting ring
> 200 g total
pyrotechnic composition or > 60 g pyrotechnic
composition per driver, ≤ 3% flash composition as report
effects, each whistle (if any) ≤ 25 g and ≤ 50 g
whistle composition per wheel
1.3G
≤ 200 g total
pyrotechnic composition and ≤ 60 g pyrotechnic
composition per driver, ≤ 3% flash composition as report
effects, each whistle (if any) ≤ 5 g and ≤ 10 g
whistle composition per wheel
1.4G
Selection pack
Display selection box, display
selection pack, garden selection box, indoor selection box;
assortment
A pack of more than one type
each corresponding to one of the types of fireworks listed
in this table
The most hazardous firework
type determines the classification
Firecracker
Celebration cracker,
celebration roll, string cracker
Assembly of tubes (paper or
cardboard) linked by a pyrotechnic fuse, each tube intended
to produce an aural effect
Each tube ≤ 140 mg of
flash composition or ≤ 1 g black powder
1.4G
Banger
Salute, flash banger, lady
cracker
Non-metallic tube containing
report composition intended to produce an aural effect
> 2 g flash composition per
item
1.1G
≤ 2 g flash composition per
item and ≤ 10 g per inner packaging
1.3G
≤ 1 g flash composition per
item and ≤ 10 g per inner packaging or ≤ 10 g black powder
per item
1.4G
Consequential
amendment: In 2.2.1.1.3, replace "2.2.1.1.7" with
"2.2.1.1.8".
2.2.2.1.5 Under the heading
"Oxidizing gases", replace "see ISO 10156:1996" with "see
ISO 10156:1996 and ISO 10156-2:2005".
2.2.3.1.1 Replace "61 °C" with "60
°C" (three times).
Consequential amendments: The same
change applies to 2.2.3.1.2 (twice), 2.2.3.1.3, 2.2.3.3, 2.2.61.3
Note k, 2.2.9.1.14, 2.3.3.1.7, 2.3.3.1.8, Figure 2.3.6, Table A
(UN Nos. 1202, 3175, 3256), Table 4.1.1.19.6 (28 times), 4.1.2.1,
5.3.2.3.2 (13 times), 6.1.5.7, 6.8.2.1.26, 6.8.2.1.27 (twice),
6.8.2.2.9, 6.8.4 Note 1, 6.9.2.14 (twice), 7.5.10, Chapter 8.5
(Additional requirement S2), 9.1.1.2 (Definition of FL
vehicle).
2.2.41.1.9 Amend (b) to read as
follows:
"(b) they are oxidizing substances
according to the classification procedure for Class 5.1 (see
2.2.51.1) except that mixtures of oxidizing substances which
contain 5% or more of combustible organic substances shall be
subjected to the classification procedure defined in Note
2;".
Add a new NOTE 2 to read as
follows and renumber the following Notes accordingly:
"NOTE 2: Mixtures of
oxidizing substances meeting the criteria of Class 5.1 which
contain 5% or more of combustible organic substances, which do
not meet the criteria mentioned in (a), (c), (d) or (e) above,
shall be subjected to the self-reactive substance classification
procedure.
A mixture
showing the properties of a self-reactive substance, type B to F,
shall be classified as a self-reactive substance of Class
4.1.
A mixture showing the
properties of a self-reactive substance, type G, according to the
principle given in 20.4.3 (g) of Part II of the Manual of
Tests and Criteria shall be considered for classification as a
substance of Class 5.1 (see 2.2.51.1).".
2.2.41.4 Add the following new
entry to the table:
SELF-REACTIVE SUBSTANCE
Concen-tration (%)
Packing
method
Control
tempera-ture (°C)
Emergency
tempera-ture (°C)
UN generic
entry
Remarks
ACETONE-PYROGALLOL
COPOLYMER
2-DIAZO-1-NAPHTHOL-5-SULPHONATE
100
OP8
3228
2.2.61.1.7 Amend the table to read
as follows:
Packing group
Oral toxicity
LD50 (mg/kg)
Dermal toxicity
LD50 (mg/kg)
Inhalation toxicity
by dusts and mists
LC50 (mg/l)
I
≤ 5
≤ 50
≤ 0.2
II
> 5 and ≤ 50
> 50 and ≤ 200
> 0.2 and ≤ 2
IIIa
> 50 and ≤ 300
> 200 and ≤ 1000
> 2 and ≤ 4
2.2.62.1.3 Amend the definition of
cultures to read as follows:
"Cultures are the result of
a process by which pathogens are intentionally propagated. This
definition does not include human or animal patient specimens as
defined in this paragraph;".
Add a new definition to read as
follows:
"Patient specimens are
human or animal materials, collected directly from humans or
animals, including, but not limited to, excreta, secreta, blood
and its components, tissue and tissue fluid swabs, and body parts
being carried for purposes such as research, diagnosis,
investigational activities, disease treatment and
prevention.".
2.2.62.1.4 Insert ", UN 3291"
after "UN 2900".
2.2.62.1.4.1 In the first
sentence, replace "disease to humans or animals" with "disease in
otherwise healthy humans or animals".
In the Table with the indicative
examples:
Under UN 2814:
- Replace "Hantaviruses causing
hantavirus pulmonary syndrome" with "Hantavirus causing
haemorrhagic fever with renal syndrome".
Consequential
amendments: Replace "hemorrhagic" with "haemorrhagic" in the
table (twice).
- Add "(cultures only)" after
"Rabies virus", "Rift Valley fever virus" and "Venezuelan equine
encephalitis virus".
- Insert an asterisk * after the
following entries:
- Escherichia coli
(verotoxigenic) (cultures only);
- Mycobacterium tuberculosis
(cultures only);
- Shigella dysenteriae type I
(cultures only).
Under UN 2900:
- Delete "African horse sickness
virus" and "Bluetongue virus".
- Insert "Velogenic" before
"Newcastle disease virus".
- Add "(cultures only)" after each
microorganism in the list.
Insert a new Note after the table
to read as follows:
"* Nevertheless, when the
cultures are intended for diagnostic or clinical purposes, they
may be classified as infectious substances of Category
B.".
2.2.62.1.4.2 Delete "except that
cultures, as defined in 2.2.62.1.3, shall be assigned to
UN 2814 or UN 2900 as appropriate".
In the Note amend the proper
shipping name to read: "BIOLOGICAL SUBSTANCE, CATEGORY
B".
2.2.62.1.5 Renumber current
2.2.62.1.5 as 2.2.62.1.5.1 and add a new 2.2.62.1.5 to read as
follows:
"2.2.62.1.5
Exemptions".
Insert the following new
sub-paragraphs:
"2.2.62.1.5.2 Substances
containing microorganisms which are non-pathogenic to humans or
animals are not subject to ADR unless they meet the criteria for
inclusion in another class.
2.2.62.1.5.3 Substances in a form
that any present pathogens have been neutralized or inactivated
such that they no longer pose a health risk are not subject to
ADR unless they meet the criteria for inclusion in another
class.
2.2.62.1.5.4 Substances where the
concentration of pathogens is at a level naturally encountered
(including foodstuff and water samples) and which are not
considered to pose a significant risk of infection are not
subject to ADR unless they meet the criteria for inclusion in
another class.".
2.2.62.1.5.5 Text of current
2.2.62.1.6. Amend the beginning of the paragraph to read as
follows:
"Dried blood spots, collected by
applying a drop of blood onto absorbent material, or faecal
occult blood screening tests and blood or blood components…".
2.2.62.1.5.6 Add a new paragraph
to read as follows:
"2.2.62.1.5.6 Human or animal
specimens for which there is minimal likelihood that pathogens
are present are not subject to ADR if the specimen is carried in
a packaging which will prevent any leakage and which is marked
with the words "Exempt human specimen" or "Exempt animal
specimen", as appropriate.
The packaging is deemed to comply
with the above requirements if it meets the following
conditions:
(a) The packaging consists of
three components:
(i) a leak-proof primary
receptacle(s);
(ii) a leak-proof secondary
packaging; and
(iii) an outer packaging of
adequate strength for its capacity, mass and intended use, and
with at least one surface having minimum dimensions of 100 mm ×
100 mm;
(b) For liquids, absorbent
material in sufficient quantity to absorb the entire contents is
be placed between the primary receptacle(s) and the secondary
packaging so that, during carriage, any release or leak of a
liquid substance will not reach the outer packaging and will not
compromise the integrity of the cushioning material;
(c) When multiple fragile primary
receptacles are placed in a single secondary packaging, they are
either individually wrapped or separated to prevent contact
between them.
NOTE: An element of
professional judgment is required to determine if a substance is
exempt under this paragraph. That judgment should be based on the
known medical history, symptoms and individual circumstances of
the source, human or animal, and endemic local conditions.
Examples of specimens which may be carried under this paragraph
include the blood or urine tests to monitor cholesterol levels,
blood glucose levels, hormone levels, or prostate specific
antibodies (PSA); those required to monitor organ function such
as heart, liver or kidney function for humans or animals with
non-infectious diseases, or for therapeutic drug monitoring;
those conducted for insurance or employment purposes and are
intended to determine the presence of drugs or alcohol; pregnancy
test; biopsies to detect cancer; and antibody detection in humans
or animals.".
2.2.62.1.6 Replace current text
with "(Reserved)".
2.2.62.1.7 Replace current text
with "(Reserved)".
2.2.62.1.11.1 Delete "or
containing Category B infectious substances in cultures" in the
first sentence and ", other than in cultures, " in the last
sentence.
Add the following NOTE at the
end:
"NOTE: Medical or
clinical wastes assigned to number 18 01 03 (Wastes
from human or animal health care and/or related research - wastes
from natal care, diagnosis, treatment or prevention of disease in
humans - wastes whose collection and disposal is subject to
special requirements in order to prevent infection) or
18 02 02 (Wastes from human or animal health care
and/or related research - wastes from research, diagnosis,
treatment or prevention of disease involving animals - wastes
whose collection and disposal is subject to special requirements
in order to prevent infection) according to the list of wastes
annexed to the Commission Decision 2000/532/EC 5 as amended, shall be classified
according to the provisions set out in this paragraph, based on
the medical or veterinary diagnosis concerning the patient or the
animal.".
2.2.62.1.11.2 Existing NOTE
becomes NOTE 1. Add a new NOTE 2 to read as follows:
"NOTE 2: Notwithstanding
the classification criteria set out above, medical or clinical
wastes assigned to number 18 01 04 (Wastes from human or
animal health care and/or related research - wastes from natal
care, diagnosis, treatment or prevention of disease in humans -
wastes whose collection and disposal is not subject to special
requirements in order to prevent infection) or 18 02 03
(Wastes from human or animal health care and/or related research
- wastes from research, diagnosis, treatment or prevention of
disease involving animals - wastes whose collection and disposal
is not subject to special requirements in order to prevent
infection) according to the list of wastes annexed to the
Commission Decision 2000/532/EC 5 as amended, are not subject to the
provisions of ADR.".
2.2.62.1.12 Add the following new
title:
"2.2.62.1.12 Infected
animals"
2.2.62.1.12.1 Current 2.2.62.1.8
becomes new 2.2.62.1.12.1. In new 2.2.62.1.12.1 add the following
new first sentence: "Unless an infectious substance cannot be
consigned by any other means, live animals shall not be used to
consign such a substance.".
Consequential
amendments: In 2.2.62.1.8 replace current text with "(Reserved)".
In 2.2.62.2 replace "2.2.62.1.8" with "2.2.62.1.12.1".
2.2.62.1.12.2 Add a new
2.2.62.1.12.2 to read as follows:
"2.2.62.1.12.2 Animal carcasses
affected by pathogens of Category A or which would be assigned to
Category A in cultures only, shall be assigned to UN 2814 or UN
2900 as appropriate.
Other animal carcasses affected by
pathogens included in Category B shall be carried in accordance
with provisions determined by the competent authority.".
2.2.7.1.2 (e) Replace "the values
specified in 2.2.7.7.2" with "the values specified in 2.2.7.7.2.1
(b), or calculated in accordance with 2.2.7.7.2.2 to
2.2.7.7.2.6".
2.2.7.2 In the definition of
"Multilateral approval", amend the first sentence to read
as follows:
"Multilateral approval
means approval by the relevant competent authority of the country
of origin of the design or shipment, as applicable and also,
where the consignment is to be carried through or into any other
country, approval by the competent authority of that
country.".
In the definition of "Specific
activity of a radionuclide", delete: "or volume".
In the definition of "Natural
Uranium" (under "Uranium-natural, depleted, enriched")
replace "chemically separated uranium" with "uranium (which may
be chemically separated)".
2.2.7.3.2 (a)(ii) Amend to read:
"natural uranium, depleted uranium, natural thorium or their
compounds or mixtures, providing they are unirradiated and in
solid or liquid form;".
2.2.7.4.6 (a) Amend to read:
"(a) The tests prescribed in
2.2.7.4.5 (a) and (b) provided the mass of the special form
radioactive material:
(i) is less than 200 g and they
are alternatively subjected to the Class 4 impact test prescribed
in ISO 2919:1999 "Radiation protection - Sealed radioactive
sources ‑ General requirements and classification"; or
(ii) is less than 500 g and they
are alternatively subjected to the Class 5 impact test prescribed
in ISO 2919:1999 "Radiation protection - Sealed Radioactive
Sources - General requirements and Classification"; and".
Consequential
amendment: In 2.2.7.4.6 (b), replace "ISO 2919:1980" with "ISO
2919:1999".
2.2.7.7.1.7 Under the title, amend
the beginning of the first sentence to read: "Unless excepted by
6.4.11.2, packages containing…".
2.2.7.7.1.8 Under the title, amend
to read as follows:
"Packages containing uranium
hexafluoride shall not contain:
(a) a mass of uranium hexafluoride
different from that authorized for the package design;
(b) a mass of uranium hexafluoride
greater than a value that would lead to an ullage smaller than 5%
at the maximum temperature of the package as specified for the
plant systems where the package shall be used; or
(c) uranium hexafluoride other
than in solid form or at an internal pressure above atmospheric
pressure when handed over for carriage.".
2.2.7.7.2.1 In the table, amend
the value in the last column for Te-121m to read "1 ×
106" instead of "1 × 105".
Amend (a) and (b) after the table
to read as follows:
"(a) A1 and/or
A2 values for these parent radionuclides include
contributions from daughter radionuclides with half-lives less
than 10 days, as listed in the following:
Mg-28
Al-28
Ar-42
K-42
Ca-47
Sc-47
Ti-44
Sc-44
Fe-52
Mn-52m
Fe-60
Co-60m
Zn-69m
Zn-69
Ge-68
Ga-68
Rb-83
Kr-83m
Sr-82
Rb-82
Sr-90
Y-90
Sr-91
Y-91m
Sr-92
Y-92
Y-87
Sr-87m
Zr-95
Nb-95m
Zr-97
Nb-97m, Nb-97
Mo-99
Tc-99m
Tc-95m
Tc-95
Tc-96m
Tc-96
Ru-103
Rh-103m
Ru-106
Rh-106
Pd-103
Rh-103m
Ag-108m
Ag-108
Ag-110m
Ag-110
Cd-115
In-115m
In-114m
In-114
Sn-113
In-113m
Sn-121m
Sn-121
Sn-126
Sb-126m
Te-118
Sb-118
Te-127m
Te-127
Te-129m
Te-129
Te-131m
Te-131
Te-132
I-132
I-135
Xe-135m
Xe-122
I-122
Cs-137
Ba-137m
Ba-131
Cs-131
Ba-140
La-140
Ce-144
Pr-144m, Pr-144
Pm-148m
Pm-148
Gd-146
Eu-146
Dy-166
Ho-166
Hf-172
Lu-172
W-178
Ta-178
W-188
Re-188
Re-189
Os-189m
Os-194
Ir-194
Ir-189
Os-189m
Pt-188
Ir-188
Hg-194
Au-194
Hg-195m
Hg-195
Pb-210
Bi-210
Pb-212
Bi-212, Tl-208, Po-212
Bi-210m
Tl-206
Bi-212
Tl-208, Po-212
At-211
Po-211
Rn-222
Po-218, Pb-214, At-218, Bi-214,
Po-214
Ra-223
Rn-219, Po-215, Pb-211, Bi-211,
Po-211, Tl-207
Ra-224
Rn-220, Po-216, Pb-212, Bi-212,
Tl-208, Po-212
Ra-225
Ac-225, Fr-221, At-217, Bi-213,
Tl-209, Po-213, Pb-209
Ra-226
Rn-222, Po-218, Pb-214, At-218,
Bi-214, Po-214
Ra-228
Ac-228
Ac-225
Fr-221, At-217, Bi-213, Tl-209,
Po-213, Pb-209
Ac-227
Fr-223
Th-228
Ra-224, Rn-220, Po-216, Pb-212,
Bi-212, Tl-208, Po-212
Th-234
Pa-234m, Pa-234
Pa-230
Ac-226, Th-226, Fr-222, Ra-222,
Rn-218, Po-214
U-230
Th-226, Ra-222, Rn-218,
Po-214
U-235
Th-231
Pu-241
U-237
Pu-244
U-240, Np-240m
Am-242m
Am-242, Np-238
Am-243
Np-239
Cm-247
Pu-243
Bk-249
Am-245
Cf-253
Cm-249"
(b) Insert "Ag-108m Ag-108" after:
"Ru-106 Rh-106".
Delete the entries for: "Ce-134,
La-134"; "Rn-220, Po-216"; "Th-226, Ra-222, Rn‑218, Po-214"; and
"U‑240, Np-240m".
2.2.7.7.2.2 In the first sentence,
delete "competent authority approval, or for international
carriage," and amend the beginning of the second sentence to read
as follows: "It is permissible to use an A2 value
calculated using a dose coefficient for the appropriate lung
absorption type as recommended by the International Commission on
Radiological Protection, if the chemical forms of each
radionuclide under both normal…".
In the table:
- Amend the second entry in the
first column to read: "Alpha emitting nuclides but no neutron
emitters are known to be present"
- Amend the third entry in the
first column to read: "Neutron emitting nuclides are known to be
present or no relevant data are available".
2.2.7.8.4 (d) and (e) Add at the
end: "except under the provisions of 2.2.7.8.5".
2.2.7.8.5 Add a new paragraph to
read as follows:
"2.2.7.8.5 In case of
international carriage of packages requiring competent authority
design or shipment approval, for which different approval types
apply in the different countries concerned by the shipment,
assignment to the category as required in 2.2.7.8.4 shall be in
accordance with the certificate of the country of origin of
design.".
2.2.7.9.7 Insert "Chapter 1.10" in
the list of provisions which do not apply.
2.2.8.1.6 Amend the beginning of
the first sentence of the second paragraph to read as
follows:
"Liquids, and solids which may
become liquid during carriage, which are judged not to cause…"
(remainder of the sentence unchanged).
2.2.9.2 Amend the second indent to
read as follows:
"- Uncleaned empty containment
vessels for apparatus such as transformers, condensers and
hydraulic apparatus containing substances assigned to UN Nos.
2315, 3151, 3152 or 3432.".
PART 3
Chapter 3.2
3.2.1 Column (11) Add the
following NOTE at the end:
"NOTE: If technically
relevant, these special provisions are not only applicable to the
portable tanks specified in column (10), but also to the portable
tanks that may be used according to the table in
4.2.5.2.5.".
Column (13) Add the following NOTE
at the end:
"NOTE: If technically
relevant, these special provisions are not only applicable to the
tanks specified in column (12), but also to the tanks that may be
used according to the hierarchies in 4.3.3.1.2 and
4.3.4.1.2.".
Table A
Modify Table A as follows:
UN No.
Column
Modification
0015, 0016 and 0303
(6)
Delete "204"
1169 (PG II/III),
1170 (PG II/III),
1197 (PG II/III),
1219 (PG II/III),
1293 (PG II/III),
1987 (PG II/III),
1993 (PG II/III),
3077 (PG III),
3082 (PG III),
3272 (PG II/III)
(6)
Insert "601"
1391
(2)
Add, at the end, "having a
flash-point above 60 °C"
(6)
Delete "282"
1649
(2)
Add, at the end, "having a
flash-point above 60 °C"
(6)
Delete "162"
2030
(2)
Add, at the end, "having a
flash-point above 60 °C"
(6)
Delete "298"
2814, 2900, 3245 and 3291
(6)
Delete "634"
1155, 1167, 1218, 1280, 1302,
2356, 2363 and 3336 (PG I)
(12)
Replace "L1,5BN" with
"L4BN"
1133, 1139, 1169, 1197, 1210,
1263, 1266, 1267, 1268, 1286, 1287, 1308, 1863, 1866, 1989,
1993, 2059 and 3295
(2)
Delete "(vapour pressure at
50 °C more than 175 kPa)" for each entry that is
assigned "640A" in column (6)
(6)
For each entry that is assigned
"640A" in column (6), delete "640A"
1133, 1139, 1169, 1197, 1210,
1263, 1266, 1267, 1268, 1286, 1287, 1308, 1863, 1866, 1989,
1993, 2059 and 3295
Delete the entries for which
"640B" is assigned in column (6)
1133, 1139, 1169, 1197, 1210,
1224, 1263, 1266, 1267, 1268, 1286, 1287, 1306, 1308, 1863,
1866, 1987, 1989, 1993, 1999, 3295 and 3336
(2)
Delete "but not more than 175
kPa" for each entry that is assigned "640C" in
column (6)
1133, 1139, 1169, 1197, 1210,
1263, 1266, 1286, 1287, 1306, 1866, 1993 and 1999
(2)
For each entry that is assigned
"640F" in column (6) replace "vapour pressure at
50 °C more than 175 kPa" with "boiling point not more
than 35 °C"
(2)
For each entry that is assigned
"640G" in column (6) replace "but not more than 175
kPa" with "boiling point of more than 35 °C"
1203
(9a)
Insert "BB2" adjacent to
"IBC02" in column (8)
1267, 1268 and 3295
Delete the entries for which
"640P" is assigned in column (6)
1267, 1268 and 3295
(6)
For each entry that is assigned
"640A" in column (6), insert "649"
Delete "V2" in column (16) for all
entries for classification code 1.4S.
(Applies to UN
Nos. 0012, 0014, 0044, 0055, 0070, 0105, 0110, 0131, 0173, 0174,
0193, 0323, 0337, 0345, 0349, 0366, 0367, 0368, 0373, 0376, 0384,
0404, 0405, 0432, 0441, 0445, 0454, 0455, 0456, 0460, 0481 and
0500)
Replace "VV9a" and "VV9b" by "VV9"
each time they appear in column (17).
(Applies to UN
Nos. 1564, 1794, 1884, 2506, 2509, 1544, 1548, 1549, 1550, 1551,
1557, 1566, 1579, 1588, 1601, 1616, 1655, 1663, 1673, 1690, 1709,
1740, 1759, 1773, 1812, 1907, 2020, 2025, 2026, 2074, 2077, 2214,
2215, 2233, 2237, 2239, 2280, 2291, 2331, 2430, 2440, 2446, 2473,
2475, 2503, 2505, 2507, 2508, 2512, 2516, 2570, 2578, 2579, 2585,
2588, 2651, 2655, 2659, 2660, 2662, 2674, 2698, 2713, 2716, 2729,
2757, 2759, 2761, 2763, 2771, 2775, 2777, 2779, 2781, 2783, 2786,
2802, 2803, 2811, 2823, 2834, 2853, 2854, 2855, 2856, 2862, 2865,
2869, 2871, 2875, 2876, 2905, 2923, 2967, 3027, 3143, 3146, 3147,
3249, 3253, 3259, 3260, 3261, 3262, 3263, 3283, 3284, 3285, 3288,
3345, 3349, 3427, 3438, 3439, 3453, 3457, 3458, 3459, 3460, 3462,
3464, 3465, 3466 and 3467)
Replace the code "LQ19" with "LQ7"
wherever it is listed in Column (7), except in the case of UN
2809.
(Applies to UN
Nos. 1556, 1583, 1591, 1593, 1597, 1599, 1602, 1656, 1658, 1686,
1710, 1718, 1719, 1731, 1755, 1757, 1760, 1761, 1783, 1787, 1788,
1789, 1791, 1793, 1805, 1814, 1819, 1824, 1835, 1840, 1848, 1851,
1887, 1888, 1897, 1902, 1903, 1908, 1935, 1938, 2021, 2024, 2030,
2205, 2206, 2209, 2225, 2235, 2269, 2272, 2273, 2274, 2279, 2289,
2290, 2294, 2299, 2300, 2311, 2320, 2321, 2326, 2327, 2328, 2431,
2432, 2433, 2470, 2491, 2496, 2501, 2504, 2511, 2515, 2518, 2525,
2533, 2564, 2565, 2580, 2581, 2582, 2586, 2609, 2656, 2661, 2664,
2667, 2669, 2672, 2677, 2679, 2681, 2688, 2689, 2693, 2730, 2732,
2735, 2739, 2747, 2753, 2785, 2788, 2790, 2801, 2810, 2815, 2817,
2818, 2819, 2820, 2821, 2829, 2831, 2837, 2849, 2872, 2873, 2874,
2902, 2903, 2904, 2922, 2937, 2941, 2942, 2946, 2991, 2992, 2993,
2994, 2995, 2996, 2997, 2998, 3005, 3006, 3009, 3010, 3011, 3012,
3013, 3014, 3015, 3016, 3017, 3018, 3019, 3020, 3025, 3026, 3055,
3066, 3140, 3141, 3142, 3144, 3145, 3172, 3264, 3265, 3266, 3267,
3276, 3278, 3280, 3281, 3282, 3287, 3293, 3320, 3347, 3348, 3351,
3352, 3410, 3411, 3413, 3414, 3415, 3418, 3421, 3422, 3424, 3426,
3429, 3434, 3435 and 3440)
Delete the code "TE15" wherever it
is listed in Column (13).
Delete the entries for the
following UN Nos.: 1366, 1370, 2005, 2445, 3051, 3052, 3053,
3076, 3433, 3461.
Consequential
amendments: Delete the entries accordingly in 2.2.42.3, 4.1.4.1
(P404), 4.1.4.4 (PR1) and 6.8.5.1.1 (a).
Delete the entries for the
following UN Nos.: 1014, 1015, 1979, 1980, 1981 and 2600.
Consequential
amendments: In 4.3.3.2.5, delete the entries accordingly in the
table.
For UN Nos. 1011, 1965 and 1978,
add "652" to column (6).
For UN Nos. 1170, 1987 and 1993
insert "330" in Column (6).
For UN Nos. 1263 and 3066, add
"TP27", "TP28" and "TP29" in column (11) for packing groups I, II
and III, respectively.
For UN Nos. 2912, 2915, 3321 and
3322, add "325" in column (6).
For UN Nos. 3324, 3325 and 3327,
add "326" in column (6).
For UN No 1013, insert "653" in
Column (6).
UN 1143 Amend the name in column
(2) to read as follows: "CROTONALDEHYDE or CROTONALDEHYDE,
STABILIZED" and add "324" in column (6).
UN 1170 Delete "PP2" from column
(9) (twice).
For UN 1202, in column (2) of the
second entry, replace "EN 590:1993" with "EN 590:2004"
(twice).
Consequential
amendments: The same modification applies to 4.1.1.19.6 (twice),
9.1.1.2, Definition of "FL vehicle" (twice).
UN 1463 Insert respectively "+6.1"
before "+8" in column (5). Replace respectively "OC2" with "OTC"
in Column (3b) and "58" with "568" in Column (20).
Add "V11 V12" in Column (16) and
insert "CV28" after "CV24" in Column (18).
UN 1614 Add "P099" in column
(8).
UN 1733 Add "T3" in column (10)
and "TP33" in column (11).
UN 1740 Amend the name in column
(2) to read: "HYDROGENDIFLUORIDES, SOLID, N.O.S."
Consequential
amendment: In 2.2.8.3 under C2, amend the name of "1740"
accordingly.
UN 1779 Amend the name in column
(2), to read as follows: "FORMIC ACID with more than 85% acid by
mass".
Insert "+3" after "8" in column
(5).
Replace respectively "C3" with
"CF1" in Column (3b), "AT" with "FL" in Column (14) and "80" with
"83" in Column (20).
Add "S2" in Column (19).
Consequential
amendment: In 4.1.1.19.6, in column (2b) of the table, amend the
name of UN 1779 accordingly.
UN 1848 Amend the name in column
(2) to read as follows: "PROPIONIC ACID with not less than 10%
and less than 90% acid by mass".
Consequential
amendment: In 4.1.1.19.6, in column (2b) of the table, amend the
name of UN 1848 accordingly.
UN 1950 Add "327" in column (6),
replace "P204" with "P003 LP02" in column (8), and add "PP17 PP87
RR6 L2" in column (9a).
UN 1956 Insert "292" in column
(6).
UN 2015 Replace "T10" with "T9" in
column (10).
UN 2030 In column (10), replace
"T20" with "T10" for packing group I and "T15" with "T7" for
packing group II, and in column (11), replace "TP2" with "TP1"
for packing group III.
UN 2037 Replace "P204" with "P003"
in Column (8), and add "PP17 RR6" in column (9a).
UN 2662 Delete this entry.
UN 2823 Amend the name in column
(2) to read: "CROTONIC ACID, SOLID".
UN 2880 For packing group II:
insert "322" in column (6);
For packing group III: replace
"316" with "313" and "314".
UN 2900 Delete "BK1 BK2" in column
(10) and delete "606" in column (20).
UN 3245 Amend the proper shipping
name in column (2) to read as follows: "GENETICALLY MODIFIED
MICROORGANISMS or GENETICALLY MODIFIED ORGANISMS".
Consequential
amendment: In 2.2.9.3 under M8, amend the name of "3245"
accordingly.
UN 3291 Add "BK2" in Column
(10).
UN 3373 Amend the proper shipping
name in column (2) to read: "BIOLOGICAL SUBSTANCE, CATEGORY B"
and add "6.2", "T1" and "TP1" in columns (5), (10) and (11),
respectively.
Consequential
amendments: In 2.2.62.3 under I4, in 4.1.8.5 and in 4.1.10.4 MP5,
amend the name of "3373" accordingly. In 2.2.62.1.3 and 2.2.62.3,
amend the title of I4 to read as follows: "Biological
substances".
UN 3435 Delete this entry.
UN 3257 Amend as follows:
(1)
(2)
(13)
3257
ELEVATED TEMPERATURE LIQUID,
N.O.S., at or above 100 °C and below its flash-point
(including molten metals, molten salts, etc.), filled at a
temperature higher than 190 °C
TU35 TC7 TE6
TE14 TE18 TE24
3257
ELEVATED TEMPERATURE LIQUID,
N.O.S., at or above 100 °C and below its flash-point
(including molten metals, molten salts, etc.), filled at or
below 190 °C
TU35 TC7 TE6
TE14 TE24
For UN Nos. 3364, 3365, 3366,
3367, 3368 and 3370, replace "wetted" with "WETTED" in
column (2).
For UN 3375, delete "TU26" in
Column (13) for both liquid and solid entries.
Add the following new entries:
UN No.
Name and
description
Class
Classification code
Packing
group
Labels
Special
provisions
Limited
quantities
Packagings
Portable
tanks and bulk containers
ADR
tanks
Vehicle
for tank carriage
Trans-port
cate-gory
Special
provisions for carriage
Hazard
identification
No.
Packing
instruction
Special
pac-king
provisions
Mixed
packing
provisions
Por-table
tank instruction
Special
provisions
Tank
code
Special
provisions
Packages
Bulk
Loading,
unloa-ding and han-dling
Opera-tion
(1)
(2)
(3a)
(3b)
(4)
(5)
(6)
(7)
(8)
(9a)
(9b)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
0015
AMMUNITION, SMOKE with or
without burster, expelling charge or propelling charge,
containing corrosive substances
1
1.2G
1
+8
LQ0
P130
LP101
PP67
L1
MP23
1
V2
CV1
CV2
CV3
S1
0016
AMMUNITION, SMOKE with or
without burster, expelling charge or propelling charge,
containing corrosive substances
1
1.3G
1
+8
LQ0
P130
LP101
PP67
L1
MP23
1
V2
CV1
CV2
CV3
S1
0303
AMMUNITION, SMOKE with or
without burster, expelling charge or propelling charge,
containing corrosive substances
1
1.4G
1.4
+8
LQ0
P130
LP101
PP67
L1
MP23
2
V2
CV1
CV2
CV3
S1
1391
ALKALI METAL DISPERSION or
ALKALINE EARTH METAL DISPERSION having a flash-point of not
more than 60 °C
4.3
WF1
I
4.3
+3
182
183
274
506
LQ0
P402
PR1
MP2
L10BN(+)
TU1 TE5 TT3 TM2
FL
1
V1
CV23
S2
S20
X323
1649
MOTOR FUEL ANTI-KNOCK MIXTURE
having a flash-point of not more than 60 °C
6.1
TF1
I
6.1
+3
LQ0
P602
MP8 MP17
T14
TP2
L10CH
TU14 TU15 …
MI skaidrojums pēc oficiālā likuma teksta. Orientējošs, neaizstāj juridisku konsultāciju.